30 June 2021 in Eastern-European Journal of Enterprise Technologies
This work deals with fluid-structure interaction (FSI), one of the emerging areas of numerical simulation and calculation. This research shows a numerical study investigating heat transfer enhancement and fluid-structure interaction in a circular finned tube by using alumina nanofluid as a working fluid with a typical twisted tape that has a twisting ratio of 1.85. The studied nanofluid volumes of fraction are φ=0, 3, 5 % under conditions of laminar and turbulent flow. The solution for such problems is based on the relations of continuum mechanics and is mostly done with numerical methods. FSI occurs when the flow of fluid influences the properties of a structure or vice versa. It is a computational challenge to deal with such problems due to complexity in defining the geometries, nature of the interaction between a fluid and solid, intricate physics of fluids and requirements of computational resources. CFD investigations were made based on the numerical finite volume techniques to solve the governing three-dimensional partial differential equations to get the influence of inserted twisted tape and concentration of nanofluid on heat transfer enhancement, friction loss, average Nusselt number, velocity profile, thermal performance factor characteristics, and two-way interaction in a circular tube at laminar and turbulent flow. The governing continuity, momentum and energy transfer equations are solved using Ansys Fluent and Transient Structural. The simulation results show that the deformations of two-way coupling fluctuate from side to side, with 0.004 mm, as maximum amplitude, located at the typical twisted tape center. Heat transfer dissipation improved by adding fins and as Reynolds numbers increase the heat transfer behavior increases.
31 January 2025 in CFD Letters
The study examines the impact of hybrid nanoparticle-based materials on the flow performance in a tube with a consistent surface temperature of 373 K. The simulation of the flow was conducted using Ansys 2024 and two-dimensional governing equations for partial differentials. This simulation utilized three distinct concentrations of hybrid nanomaterials Al2O3–Cu to observe their effects. Al2O3–Cu nanoparticles are dispersed in water at volume ratios of 1%, 5%, and 100%. The fluid velocity varied between 0.1 and 1.5 m/s, while the input temperature was 25 °C (~298 K). The current study examines three cases of dimples: 15, 30, and 45 concave/convex dimples. Increasing the concentration of Al2O3-Cu nanoparticles in water is shown to improve certain physical properties while decreasing others. Moreover, when the concentration of nanoparticles grows, the Nusselt number (Nu) also rises. The thermal performance factor is enhanced with an increase in the number of dimples. The study shows that the heat transfer coefficient increases with hybrid nanoparticle concentration, achieving enhancements of 2.14%, 10.8%, and 21.82% for 1%, 5%, and 10% concentrations at 1 m/s. The highest increase of 22.22% compared to pure water occurs at 1.5 m/s with a 10% concentration. Compared to a smooth pipe, improvements are 15.67%, 30.01%, and 37.72% for three cases, with case 2 (30 concave/convex dimples) exhibiting the best thermal performance factor.
20 December 2019 in Journal of Engineering and Applied Sciences
HHHasanen Mohammed Hussen
Experimental and Numerical Study in Horizontal Tube by using Swirl Device
30 August 2022 in Eastern-European Journal of Enterprise Technologies
With the development of simulation technology and the ability to obtain accurate numerical results, as well as with the development of information technology, software that can solve numerical problems has become necessary to see physical changes that cannot be seen by the human eye. Multiphase stream field is settled utilizing the volume of fluid (VOF) method, and the flow equations are assessed and addressed mathematically by the notable limited volume approach. As a multiphase framework without mass exchange, air/water stream is considered. For practically all cases considered in this review, the heat transfer coefficient is higher. In any case, a critical punishment pressure drop was observed especially for high mass courses through undulating channels. A wavy channel with a variable wave height was simulated to see the variables of the flow process for multi-phase materials with a square cross-section, where different speeds were used for the inlet duct for air, water and steam. The results proved that the increase in the height of the channel wall wave works to obstruct the flow and thus increases the time required for the fluid to reach the exit area. The value of time required for steam and air to reach the exit area at the channel wall wave height of 25 mm and the flow velocity of 0.1 m/s was 6.01 s, which is the longest time it took for the fluid to reach the exit area compared to other cases. The pressure value reflects the amount of turbulence in the flow process, and it's crucial for thermal improvements based on flow turbulence. The entrance flow velocity is 0.1 m/s and the wall wave height is 25 mm at a time of 2 s, when the pressure reaches 873.7 Pa.
26 April 2024 in Mathematical Modelling of Engineering Problems
SRSafaa Mohammed Ali Mohammed Reda
Safaa Mohammed Ali Mohammed Reda