The North America-based Tropospheric Ozone Lidar Network (TOLNet) was recently established to provide high spatiotemporal vertical profiles of ozone, to better understand physical processes driving tropospheric ozone variability and to validate the tropospheric ozone measurements of upcoming spaceborne missions such as Tropospheric Emissions: Monitoring Pollution (TEMPO). The network currently comprises six tropospheric ozone lidars, four of which are mobile instruments deploying to the field a few times per year, based on campaign and science needs. In August 2016, all four mobile TOLNet lidars were brought to the fixed TOLNet site of JPL Table Mountain Facility for the 1-week-long Southern California Ozone Observation Project (SCOOP). This intercomparison campaign, which included 400 h of lidar measurements and 18 ozonesonde launches, allowed for the unprecedented simultaneous validation of five of the six TOLNet lidars. For measurements between 3 and 10 km a.s.l., a mean difference of 0.7 ppbv (1.7 %), with a root-mean-square deviation of 1.6 ppbv or 2.4 %, was found between the lidars and ozonesondes, which is well within the combined uncertainties of the two measurement techniques. The few minor differences identified were typically associated with the known limitations of the lidars at the profile altitude extremes (i.e., first 1 km above ground and at the instruments' highest retrievable altitude). As part of a large homogenization and quality control effort within the network, many aspects of the TOLNet in-house data processing algorithms were also standardized and validated. This thorough validation of both the measurements and retrievals builds confidence as to the high quality and reliability of the TOLNet ozone lidar profiles for many years to come, making TOLNet a valuable ground-based reference network for tropospheric ozone profiling.
As part of the Network for the Detection of Atmospheric Composition Change (NDACC), ground-based measurements obtained from the Jet Propulsion Laboratory (JPL) stratospheric ozone lidar and the NOAA stratospheric aerosol lidar at Mauna Loa, Hawaii, over the past 2 decades were used to investigate the impact of volcanic eruptions and pyrocumulonimbus (PyroCb) smoke plumes on the stratospheric aerosol load above Hawaii since 1999. Measurements at 355 and 532 nm conducted by these two lidars revealed a color ratio of 0.5 for background aerosols and small volcanic plumes and 0.8 for a PyroCb plume recorded on September 2017. Measurements of the Nabro plume by the JPL lidar in 2011–2012 showed a lidar ratio of (64±12.7) sr at 355 nm around the center of the plume. The new Global Space-based Stratospheric Aerosol Climatology (GloSSAC), Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) Level 3 and Stratospheric Aerosol and Gas Experiment III on the International Space Station (SAGE III-ISS) stratospheric aerosol datasets were compared to the ground-based lidar datasets. The intercomparison revealed a generally good agreement, with vertical profiles of extinction coefficient within 50 % discrepancy between 17 and 23 km above sea level (a.s.l.) and 25 % above 23 km a.s.l. The stratospheric aerosol depth derived from all of these datasets shows good agreement, with the largest discrepancy (20 %) being observed between the new CALIOP Level 3 and the other datasets. All datasets consistently reveal a relatively quiescent period between 1999 and 2006, followed by an active period of multiple eruptions (e.g., Nabro) until early 2012. Another quiescent period, with slightly higher aerosol background, lasted until mid-2017, when a combination of extensive wildfires and multiple volcanic eruptions caused a significant increase in stratospheric aerosol loading. This loading maximized at the very end of the time period considered (fall 2019) as a result of the Raikoke eruption, the plume of which ascended to 26 km altitude in less than 3 months.
The National Aeronautics and Space Administration’s (NASA) Deep Space Optical Communications (DSOC) payload, launched with the Psyche spacecraft on October 13, 2023, is facilitating an ongoing Technology Demonstration (TD) of Free-Space Optical Communications (FSOC), from beyond the earth-moon system. The DSOC Flight Laser Transceiver (FLT), can acquire a 1064 nm uplink laser from earth, and return a 1550 nm, Serially Concatenated Pulse Position Modulated (SCPPM) signal, to earth. The FLT uses a 22 cm diameter unobscured optical transceiver assembly, coupled to a 4 W average power laser transmitter, supplemented with actuators, sensors, electronics and software. A 5-7 kW average power, multi-beam 1064 nm uplink laser assembly integrated to the Optical Communications Telescope Laboratory (OCTL) near Wrightwood, CA serves as the Ground Laser Transmitter (GLT). The DSOC Ground Laser Receiver (GLR) at the Palomar Observatory, Hale telescope (operated by Caltech Optical Observatories), consists of a Superconducting Nanowire Single Photon Detector (SNSPD) array, connected to a ground signal processing assembly. Signal photon arrivals are detected and processed to extract information codewords at the GLR. A Mission Operations System (MOS) co-located with the Psyche Project Mission Operations Center, at the Jet Propulsion Laboratory (JPL), coordinates DSOC technology demonstration activities. This paper presents a system overview, mission description and operations architecture for the TD. Early results that include downlink at maximum downlink data-rate of 267 Mb/s from 0.37 Astronomical Units (AU) or 55 million kilometers are presented.
28 January 2019 in Atmospheric Measurement Techniques
As part of international efforts to monitor air quality, several satellite missions such as the Tropospheric Monitoring Instrument (TROPOMI) were deployed and others, like Tropospheric Emissions: Monitoring Pollution (TEMPO), are planned for the near future. In support of the validation of these missions, major upgrades to the tropospheric ozone lidar located at the Jet Propulsion Laboratory Table Mountain Facility (TMF) were recently performed. These modifications include the full automation of the system, which now allows unattended measurements during frequent satellite overpasses, and a new receiver that extends the measurement capabilities of the system down to 100 m above surface. The automation led to the systematic operation of the lidar during daily TROPOMI overpasses, providing more than 139 reference profiles since January 2018. Ozone profiles retrieved using the new lidar receiver were compared to ozonesonde profiles obtained from a co-located tethered balloon. An agreement of about 5 % with the ozonesonde down to an altitude range of 100 m a.g.l. was observed. Furthermore, the stability of the receiver configuration was investigated. Comparisons between the lowest point retrieved by the lidar and a co-located surface ozone photometer showed no sign of drift over a 2-month test period and an agreement better than 10 %. Finally, measurements from a 24 h intensive measurement period during a stratospheric intrusion event showed good agreement with two free-flying ozonesondes. These comparisons revealed localized differences between sonde and lidar, possibly owing to the differing vertical resolutions (between 52 and 380 m for lidar and about 100 m for the sonde).
This paper discusses the development of optimization tools to support the design and installation of automated material handling systems. The paper is motivated by current research by the authors involving the design and development of an automated tray management system (TMS) by the United States Postal Service. Upon final contract award, the TMS project is expected to become the largest material handling contract in history. In summary, the paper introduces current design issues related to TMS, introduces new IP and network optimization tools, and describes a user interface to isolate users from detailed model building using cumbersome optimization methods. The case study environment provides a means of validating methods and ensures that the methods presented in the paper are both timely in terms of industry interest and pragmatic in use.