We have demonstrated a laser-produced plasma extreme ultraviolet source operating in the 6.5–6.7 nm region based on rare-earth targets of Gd and Tb coupled with a Mo/B4C multilayer mirror. Multiply charged ions produce strong resonance emission lines, which combine to yield an intense unresolved transition array. The spectra of these resonant lines around 6.7 nm (in-band: 6.7 nm ±1%) suggest that the in-band emission increases with increased plasma volume by suppressing the plasma hydrodynamic expansion loss at an electron temperature of about 50 eV, resulting in maximized emission.
We characterize extreme ultraviolet (EUV) emission from mid-infrared (mid-IR) laser-produced plasmas (LPPs) of the rare-earth element Gd. The energy conversion efficiency (CE) and the spectral purity in the mid-IR LPPs at λL = 10.6 μm were higher than for solid-state LPPs at λL = 1.06 μm, because the plasma produced is optically thin due to the lower critical density, resulting in a CE of 0.7%. The peak wavelength remained fixed at 6.76 nm for all laser intensities studied. Plasma parameters at a mid-IR laser intensity of 1.3×1011 W/cm2 was also evaluated by use of the hydrodynamic simulation code to produce the EUV emission at 6.76 nm.
Bright narrow band emission observed in optically thin plasmas of high-Z elements in the extreme ultraviolet spectral region follows a quasi-Moseley's law. The peak wavelength can be expressed as , where R∞ is the Rydberg constant. The wavelength varies from 13.5 nm to 4.0 nm as the atomic number, Z, increases from Z = 50 to Z = 83. The range of emission wavelengths available from hot optically thin plasmas permits the development of bright laboratory-scale sources for applications including x-ray microscopy and x-ray absorption fine structure determination.
We have investigated the dependence of the spectral behavior and conversion efficiencies of rare-earth plasma extreme ultraviolet sources with peak emission at 6.7 nm on laser wavelength and the initial target density. The maximum conversion efficiency was 1.3% at a laser intensity of 1.6×1012 W/cm2 at an operating wavelength of 1064 nm, when self-absorption was reduced by use of a low initial density target. Moreover, the lower-density results in a narrower spectrum and therefore improved spectral purity. It is shown to be important to use a low initial density target and/or to produce low electron density plasmas for efficient extreme ultraviolet sources when using high-Z targets.
We studied Extreme Ultra-Violet (EUV) emission characteristics of the 13.5 nm wavelength from CO2 laser-irradiated pre-formed tin plasmas using 2D radiation hydrodynamic simulations. Our results indicate that when a CO2 laser irradiates pre-formed tin plasma, the heated plasma expands towards the surrounding plasma, steepening the density at the ablation front and lowering the density near the laser axis due to the transverse motion of the plasma. Consequently, the laser absorption fraction decreases, and the contribution to EUV output from the ablation front becomes dominant over that from the low-density plasmas. We estimated that an EUV conversion efficiency of 10% from laser to EUV emission could be achieved with a larger laser spot size, shortened laser pulse width, and longer pre-formed plasma density scale length. Our results offer one optimizing solution to achieve an efficient and powerful EUV light source for the next-generation semiconductors.
Vectorial vortex analysis is used to determine the polarization states of an arbitrarily polarized terahertz (0.1–1.6 THz) beam using THz achromatic axially symmetric wave (TAS) plates, which have a phase retardance of Δ = 163° and are made of polytetrafluorethylene. Polarized THz beams are converted into THz vectorial vortex beams with no spatial or wavelength dispersion and the unknown polarization states of the incident THz beams are reconstructed. The polarization determination is also demonstrated at frequencies of 0.16 and 0.36 THz. The results obtained by solving the inverse source problem agree with the values used in the experiments. This vectorial vortex analysis enables a determination of the polarization states of the incident THz beam from the THz image. The polarization states of the beams are estimated after they pass through the TAS plates. The results validate this new approach to polarization detection for intense THz sources. It could find application in such cutting edge areas of physics as nonlinear THz photonics and plasmon excitation, because TAS plates not only instantaneously elucidate the polarization of an enclosed THz beam but can also passively control THz vectorial vortex beams.