This is an Open Access Article. It is published by Elsevier under the Creative Commons Attribution 4.0 Unported Licence (CC BY). Full details of this licence are available at : http://creativecommons.org/licenses/by/4.0/A three-phase axisymmetric numerical model based on Volume of Fluid–Continuum Surface Force (VOF–CSF) model was developed to perform parametric analysis of compound droplet production in three-phase glass capillary devices that combine co-flow and countercurrent flow focusing. The model predicted successfully generation of core-shell and multi-cored double emulsion droplets in dripping and jetting (narrowing and widening) regime and was used to investigate the effects of phase flow rates, fluid properties, and geometry on the size, morphology, and production rate of droplets. As the outer fluid flow rate increased, the size of compound droplets was reduced until a dripping-to-jetting transition occurred. By increasing the middle fluid flow rate, the size of compound droplets increased, which led to a widening jetting regime. The jetting was supressed by increasing the orifice size in the collection capillary or increasing the interfacial tension at the outer interface up to 0.06 N/m. The experimental and simulation results can be used to encapsulate CO2 solvents within gas-permeable microcapsules
12 October 2015 in ACS Applied Materials & Interfaces
Biodegradable poly(dl-lactic acid) (PLA) and poly(lactic-co-glycolic acid) (PLGA) microparticles with tunable size, shape, internal structure and surface morphology were produced by counter-current flow focusing in axisymmetric (3D) glass capillary devices. The dispersed phase was composed of 0.5–2 wt % polymer solution in a volatile organic solvent (ethyl acetate or dichloromethane) and the continuous phase was 5 wt % aqueous poly(vinyl alcohol) solution. The droplets with a coefficient of variation in dripping regime below 2.5% were evaporated to form polymeric particles with uniform sizes ranging between 4 and 30 μm. The particle microstructure and surface roughness were modified by adding nanofiller (montmorillonite nanoclay) or porogen (2-methylpentane) in the dispersed phase to form less porous polymer matrix or porous particles with golf-ball-like dimpled surface, respectively. The presence of 2–4 wt % nanoclay in the host polymer significantly reduced the release rate of paracetamol and prevented ...
1 July 2015 in Journal of Colloid and Interface Science
Pinch-off of a compound jet in 3D glass capillary microfluidic device, which combines co-flowing and countercurrent flow focusing geometries, was investigated using an incompressible three-phase axisymmetric Volume of Fluid-Continuum Surface Force (VOF-CSF) numerical model. The model showed good agreement with the experimental drop generation and was capable of predicting formation of core/shell droplets in dripping, narrowing jetting and widening jetting regimes. In dripping and widening jetting regimes, the presence of a vortex flow around the upstream end of the necking thread facilitates the jet break-up. No vortex flow was observed in narrowing jetting regime and pinch-off occurred due to higher velocity at the downstream end of the coaxial thread compared to that at the upstream end. In all regimes, the inner jet ruptured before the outer jet, preventing a leakage of the inner drop into the outer fluid. The necking region moves at the maximum speed in the narrowing jetting regime, due to the highest level of shear at the outer surface of the thread. However, in widening jetting regime, the neck travels the longest distance downstream before it breaks.
1 July 2017 in Journal of Colloid and Interface Science
Core-shell microcapsules and crescent-shaped microparticles can be used as picolitre bioreactors for cell culture and microwells for cell trapping/immobilisation, respectively. Monodisperse polylactic acid (PLA) core-shell microcapsules with a diameter above 200μm, a shell thickness of 10μm, and 96% water entrapment efficiency were produced by solvent evaporation from microfluidically generated W/O/W emulsion drops with core-shell structure, and used to encapsulate Saccharomyces cerevisiae yeast cells in their aqueous cores. The morphological changes of the capsules stained with Nile red were studied over 14days under different osmotic pressure and pH gradients. The shell retained its integrity under isotonic conditions, but buckling and particle crumbling occurred in a hypertonic solution. When the capsules containing 5wt% aqueous Eudragit® S 100 solution in the core were incubated in 10-4M HCl solution, H+ diffused through the PLA film into the core causing an ionic gelation of the inner phase and its phase separation into polymer-rich and water-rich regions, due to the transition of Eudragit from a hydrophilic to hydrophobic state. Crescent-shaped composite microparticles with Eudragit cores and PLA shells were fabricated by drying core-shell microcapsules with gelled cores, due to the collapse of PLA shells encompassing water-rich crescent regions.
1 March 2014 in Journal of Colloid and Interface Science
Droplet size in microfluidic devices is affected by wettability of the microfluidic channels. Three-dimensional countercurrent flow focusing using assemblies of chemically inert glass capillaries is expected to minimize wetting of the channel walls by the organic solvent. Monodispersed polycaprolactone and poly(lactic acid) particles with a diameter of 18-150 μm were produced by evaporation of solvent (dichloromethane or 1:2 mixture of chloroform and toluene) from oil-in-water or water-in-oil-in-water emulsions produced in three-dimensional flow focusing glass capillary devices. The drop generation behaviour was simulated numerically using the volume of fluid method. The numerical results showed good agreement with high-speed video recordings. Monodispersed droplets were produced in the dripping regime when the ratio of the continuous phase flow rate to dispersed phase flow rate was 5-20 and the Weber number of the dispersed phase was less than 0.01. The porosity of polycaprolactone particles increased from 8 to 62% when 30 wt% of the water phase was incorporated in the organic phase prior to emulsification. The inner water phase was loaded with 0.156 wt% lidocaine hydrochloride to achieve a sustained drug release. 26% of lidocaine was released after 1 h and more than 93% of the drug was released after 130 h.
This paper is in closed access until 23rd September 2018.A long-term production stability of oil-in-water emulsions by microchannel (step) emulsification was investigated using two cross flow silicon chips consisting of 540 or 1,850 microchannels fabricated on 10 parallel terraces. Each terrace was 9.54 mm long and consisted of 54 channels with a depth of 5 µm and a width of 18 µm (chip 1) or 185 channels with a depth of 4 µm and a width of 8 µm (chip 2). The dispersed phase was a mixture of 2 wt% polycaprolactone (PCL) and 1 wt% poly(d,l-lactic) acid (PLA) dissolved in dichloromethane and the continuous phase was 2 wt% poly(vinyl alcohol). After solvent evaporation, the droplets were transformed into highly uniform composite polymer particles with an average diameter of 8.8 or 4.9 µm. The percentages of active channels, droplet sizes and droplet generation frequencies at individual terraces were investigated in both chips to reveal any flow maldistribution. After 6 h of production in chip 1, overall 95% of the channels produced droplets and the percentage of active channels on each terrace was at least 91%. The percentage of active channels decreased by decreasing the size of the channels. The mean droplet size varied negligibly across individual terraces over 7 h. Slightly higher droplet generation frequencies and smaller percentages of active channels were observed at central terraces. The droplet generation frequencies at the channels located close to each other were similar, indicating that droplet formation dynamics was coupled. The droplet size was not affected by the dispersed phase flow rate