Dye-sensitized solar cells (DSSCs) are a feasible option for photovoltaic energy. Zinc oxide is an n-type semiconductor employed as photoanode on DSSCs. ZnO thin films were electrodeposited to study the effects of different potentials applied during deposition. SEM images, XRD and UV-Vis analysis were conducted to reveal the morphologic, structural and optical properties of the films at three potentials. DSSCs were assembled and the photovoltaic parameters were obtained through J-V plots. DSSC with 0.031% of efficiency was demonstrated at -1.4 V of deposition potential.
Nanoparticles of TiO2 have been the main semiconductor applied in Dye-sensitized solar cells (DSSCs). In this work, titanate nanotubes (NaTiNT) and nanoribbons, were obtained by the hydrothermal method from TiO2 anatase. These materials were deposited on conductive substrate by electrophoresis, with and without thermal treatment, sensitized by ruthenium-based dye and used as work electrode. Exposing those photovoltaic devices to visible radiation, with films before thermal treatment, a short-circuit current density (JSC) of 0.0012 mA/cm2 was observed for the cell with NaTiNT, a current density of 0.0398 mA/cm2 for the cell with Nanoribbons, and a current density of 0.4028 mA/cm2 for the cell with TiO2 as electrode. After thermal treatment, a short-circuit current density of 0.4269 mA/cm2 was observed for the cell with NaTiNT, a current density of 0.0765 mA/cm2 for the Nanoribbons cell, and, finally, a current density of 0.3310 mA/cm2 for the cell with TiO2 as electrode. The new morphological, structural and optical characteristics of these nanoparticles may contribute for the development and research of new generation photovoltaic devices.
Nanoparticles of TiO2 have been the main semiconductor applied in Dye-sensitized solar cells (DSSCs). In this work, solar cells were developed from the electrophoretic deposition of anatase titanium dioxide (TiO2) films on conductive glasses. The electrophoretic deposition was perfomed with a constant voltage of 80V for 2 minutes and, after drying, the films were sintered at three different temperatures: 450 °C, 550 °C and 600 °C. In the assembly of the cells, the titanium dioxide films were sensitized by Ruthenizer 535-bisTBA dye (N719) and an electrolyte containing the iodide / tri-iodide redox pair and a commercial transparent platinum counter electrode were used. TiO2 films were characterized by scanning electron microscopy, dispersive energy spectroscopy and X-ray diffraction and photo-electrochemical techniques. The energy conversion rates were 0.2646% for the sintered film at 450 °C, 0.1209% for the sintered film at 550 °C and 0.1137% for the film sintered at 600 °C.
Titanate nanotubes (TiNTs) with the chemical composition Na2Ti3O7.nH2O (NaTiNT) were obtained through a hydrothermal method in highly alkaline medium. Protonated titanates nanotubes (H-TiNTs), with the composition H2Ti3O7.nH2O, were prepared by ion exchange reaction through a suspension of Na2Ti3OγnH2O nanotubes in HCl medium, promoting the exchange of Na+ ions by H+. Both Na2Ti3O7.nH2O and H2Ti3O7.nH2O products, as well the TiO2 used as raw material for the nanotubes processing, were used as starting material for the solar cells photoelectrodes sensitized using mesoporphyrin extracted from a precursor of cashew nut shell. Exposing the NaTiNT sample to solar radiation of 1258 W/m2, a short-circuit current density (ISC) of 13 µA/cm2 and an open-circuit voltage (VOC) of 370 mV were registered and, a current density of 7.6 µA/cm2 and a voltage of 256 mV for the prototype cell based on H-TiNTs. A current density of 1.1 µA/cm2 and an open-circuit voltage of 1.6 mV were obtained for the cell using TiO2 as electrode.