Jan Burek

Jan Burek

Auto-generated profile, based on publicly available information

Jan Burek

Rzeszów University of Technology

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 January 2021 in Materials
Verified
Journal Article
Open access
PDF file
JBJan Burek
Jan Burek
RBRobert Babiarz
Robert Babiarz
JBJarosław Buk
Jarosław Buk
Paweł SułkowiczPaweł Sułkowicz
Paweł Sułkowicz
KKKrzysztof Krupa
Krzysztof Krupa
Servicing aircraft engines sometimes requires manufacturing only a single piece of a given part. Manufacturing a turbine disc using traditional methods is uneconomical. It is necessary to use a different machining method recommended for small lot production. One of the proposed methods is WEDM (wire electrical discharge machining). The article presents the results of the research on finishing WEDM of Inconel 718 turbine disc fir tree slots. The influence of infeed, mean gap voltage, peak current, pulse off-time, and discharge energy on the shape accuracy, surface roughness, microcracks, and the white layer thickness were determined. Mathematical models were developed based on the DoE (Design of Experiment) analysis. The statistical significance of the models was verified with the ANOVA (Analysis of Variance) test. The machining parameters control methods that allow achieving the required shape accuracy, surface roughness, and surface layer condition were presented. The obtained surface roughness was Ra = 0.84 μm, the shape accuracy of the slot in the normal-to-feed direction was Δd = 0.009 μm, the profile shape accuracy was Δr = 0.033 μm, and the thickness of recast (white) layer was approximately 5 μm.

1 November 2022 in Acta Mechanica et Automatica
Verified
Journal Article
Open access
PDF file
Paweł SułkowiczPaweł Sułkowicz
Paweł Sułkowicz
RBRobert Babiarz
Robert Babiarz
JBJan Burek
Jan Burek
JBJarosław Buk
Jarosław Buk
KGKamil Gancarczyk
Kamil Gancarczyk
The article presents a method of increasing the shape and dimensional accuracy of low-stiffness shafts manufactured in a single pass of a grinding wheel in traverse grinding. One-pass manufacturing is one of the ways for reducing machining time and increasing efficiency, thus lowering production costs. However, maintaining the necessary accuracy proves to be a challenge because the whole machining allowance has to be removed at once, leaving no room for errors that could be fixed in additional passes of the tool. It is especially true in finishing operations, such as traverse grinding. In addition, grinding the workpiece in a single pass of a grinding wheel leads to high forces, which cause elastic deformation of the part. The lower the stiffness of the part, the more difficult it is to achieve the required accuracy. As a result, there are many methods of improving the accuracy of grinding such parts, but they tend to be either expensive or reduce the machining efficiency. Thus, it is important to seek new methods that would allow improving the accuracy of the machining without reducing its efficiency. The proposed method does not require using steady rests and is based on the measurement of the normal grinding force component. Knowing the value of the grinding force when grinding with a set grinding depth, the elastic deformation of the machine tool–tool–workpiece system is calculated in each position of the grinding wheel. Based on the calculated deformation, the additional infeed of the grinding wheel is implemented in order to stabilise real grinding depth and to increase the accuracy of the produced part. The experimental tests were conducted to prove the effectiveness of the proposed method.

1 November 2017 in Mechanik
Verified
Journal Article
Open access
JBJan Burek
Jan Burek
ŁŻŁukasz Żyłka
Łukasz Żyłka
MPMarcin Płodzień
Marcin Płodzień
Paweł SułkowiczPaweł Sułkowicz
Paweł Sułkowicz
JBJarosław Buk
Jarosław Buk

1 February 2015 in Mechanik
Verified
Journal Article
Open access
JBJan Burek
Jan Burek
Michał GdulaMichał Gdula
Michał Gdula
MPMarcin Płodzień
Marcin Płodzień
JBJarosław Buk
Jarosław Buk
Artykuł Kształtowanie zarysu zęba koła zębatego w programowaniu dialogowym i parametrycznym | Mechanik Miesięcznik Naukowo-Techniczny

1 September 2015 in Mechanik
Verified
Journal Article
Open access
JBJan Burek
Jan Burek
RBRobert Babiarz
Robert Babiarz
MSMarcin Sałata
Marcin Sałata
MPMarcin Płodzień
Marcin Płodzień
Artykuł Wpływ siły szlifowania na odkształcenia sprężyste długich frezów pełnowęglikowych | Mechanik Miesięcznik Naukowo-Techniczny

1 January 2017 in Mechanik
Verified
Journal Article
Open access
JBJan Burek
Jan Burek
PŻPiotr Żurek
Piotr Żurek
Michał GdulaMichał Gdula
Michał Gdula
KŻKarol Żurawski
Karol Żurawski
MSMarcin Sałata
Marcin Sałata
Artykuł Dynamiczna symulacja obróbki pięcioosiowej z wykorzystaniem wirtualnej maszyny w systemie NX * | Mechanik Miesięcznik Naukowo-Techniczny