Rudolph G Buchheit

Rudolph G Buchheit

Auto-generated profile, based on publicly available information

Rudolph G Buchheit

Fontana Corrosion Center, Department of Materials Science and Engineering, The Ohio State University, Columbus, Ohio 43210, USA

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2013 in ECS Electrochemistry Letters
Verified
Journal Article
Closed access
PDF file
KRK. D. Ralston
K. D. Ralston
RBR. G. Buchheit
R. G. Buchheit
Aqueous tetrahedrally coordinated vanadate species have been recognized as corrosion inhibitors of AA2024-T3. Inhibition is primarily attributed to the suppression of the oxygen reduction reaction on Cu-containing intermetallics. This work focuses on whether aqueous vanadates provide similar inhibition to other wrought precipitation age-hardened aluminum alloys like AA6061-T6 and AA7075-T6, which contain less Cu than AA2024-T3. A combination of open circuit potential measurements, potentiodynamic polarization experiments, and exposure tests in dilute vanadate and vanadate-free NaCl solutions indicate that vanadates provide the strongest inhibition on AA2024-T3 and AA7075-T6 with relatively less inhibition observed on AA6061-T6.

9 May 2025 in Corrosion Science
Verified
Journal Article
Closed access
SKShravan Kairy
Shravan Kairy
YWY. Wu
Y. Wu
STSuzana Turk
Suzana Turk
ASA. Shekhter
A. Shekhter
RBR.G. Buchheit
R.G. Buchheit
NBN. Birbilis
N. Birbilis

7 July 2006 in ECS Transactions
Verified
Journal Article
Open access
PDF file
GKGirdhari Kumar
Girdhari Kumar
RBRudolph G Buchheit
Rudolph G Buchheit
In the present study, chitosan was used as the basis for corrosion resistant coating. Chitosan suffers from two inherent weaknesses as a coating material namely high hydrophilicity and poor adhesive strength with Al 2024 T3 alloy. In the present study, chitosan structure was modified using epoxy functional silane and vanadate. Performance of coatings was tested using EIS, adhesion testing and salt spray testing. The best salt spray performance was observed in case of chitosan-(3-Glycidoxypropyl)-trimethoxysilane-vanadate coatings, which lasted 450 hours in salt spray chamber. UV/Visible measurements showed release of vanadate by chitosan increases with increasing solution pH. This property of chitosan provides self-healing characteristics to these coatings. When the solution pH is readjusted to a lower value, chitosan can re-adsorb released vanadate. FTIR spectra of chitosan gel showed adsorption of vanadate at protonated amine sites. Chitosan showed a maximum in the vanadate adsorption capacity in the pH 3 to 5 range.

1 January 2005 in Electrochemical and Solid-State Letters
Verified
Journal Article
Closed access
PDF file
YYYuhchae Yoon
Yuhchae Yoon
RBR. G. Buchheit
R. G. Buchheit
Thin film compositional analogs of the intermetallic compound η, ( atom %), found in high strength Al-Zn-Mg-Cu alloys were fabricated using a flash evaporation technique for characterization of electrochemical behavior and for chromate conversion coating formation experiments. In potentiodynamic polarization measurements in deaerated 0.1 M NaCl, the open-circuit and breakdown potentials increased and dissolution rates decreased with increasing Cu content of the analogs. When the analogs were chromate conversion coated from a ferricyanide-accelerated coating bath, Raman spectra showed that coating thicknesses decreased with increasing Cu content. Other coating formation experiments showed that ferricyanide additions to the coating bath acted as a coating formation accelerator for . However, coating formation was so strongly inhibited for the Cu-bearing analogs, that the effect of ferricyanide on coating formation was indiscernible.

27 February 1994
Verified
Conference Paper
Open access
CDC. A. Drewien
C. A. Drewien
RBR. G. Buchheit
R. G. Buchheit
Hydrotalcite coatings on aluminum alloys are being developed for corrosion protection of aluminum in aggressive saline environments. The coating bath composition, surface pretreatment, and alloying elements in aluminum all influence the performance of these coatings during salt spray testing. The coating bath, comprised of lithium carbonate, requires aging by dissolution of aluminum into the bath in order to grow corrosion resistant coatings. Coatings formed in non-aged baths do not perform well in salt spray testing. The alloying elements in aluminum alloys, especially copper, influence the coating growth and formation leading to thin coatings. The effect of the alloy elements is to increase the open circuit potential to a level where the hydrogen evolution and corresponding aluminum dissolution reactions are limited, so that hydrotalcite coating formation and growth are limited.