22 September 2012 in Journal of Geophysical Research: Earth Surface
Using numerical models, we evaluate hydrogeological regime changes in high‐latitude river basins under conditions of ground surface warming. These models describe transient heat‐ and fluid flow coupled to the hydrogeological impacts of phase‐changes from ice to liquid water. We consider an idealized unconsolidated sedimentary aquifer system in which groundwater flow is driven by topography, representing a series of small drainage basins in riverine terrain of relatively subdued topography. Various temporal and spatial surface temperature conditions are considered to control the initial permafrost distributions for the simulations. The simulated rates of increase in groundwater contribution to streamflow during and after permafrost thaw, are in the order of magnitude comparable to hydrogeological regime changes over the past decades as reported for several (sub‐)Arctic rivers. The simulations further show that two distinct features of the subsurface response control the temporal evolution of base flow increase: (1) shifts in aquifer permeability architecture during permafrost degradation and (2) uptake of water into aquifer storage when sub‐permafrost hydraulic heads rise. Model analysis shows that the latter process delays base flow increase by several decades to centuries. In order to evaluate the relative importance of both processes in natural systems, the current hydraulic regime of sub‐permafrost aquifer systems as well as patterns of permafrost heterogeneity, taliks and their hydraulic connectivity are insufficiently known.
25 March 2013 in Geophysical Research Letters
We show how fully distributed space‐time measurements with Fiber‐Optic Distributed Temperature Sensing (FO‐DTS) can be used to investigate groundwater flow and heat transport in fractured media. Heat injection experiments are combined with temperature measurements along fiber‐optic cables installed in boreholes. Thermal dilution tests are shown to enable detection of cross‐flowing fractures and quantification of the cross flow rate. A cross borehole thermal tracer test is then analyzed to identify fracture zones that are in hydraulic connection between boreholes and to estimate spatially distributed temperature breakthrough in each fracture zone. This provides a significant improvement compared to classical tracer tests, for which concentration data are usually integrated over the whole abstraction borehole. However, despite providing some complementary results, we find that the main contributive fracture for heat transport is different to that for a solute tracer.
19 April 2014 in Water Resources Research
We show how a distributed borehole flowmeter can be created from armored Fiber Optic cables with the Active-Distributed Temperature Sensing (A-DTS) method. The principle is that in a flowing fluid, the difference in temperature between a heated and unheated cable is a function of the fluid velocity. We outline the physical basis of the methodology and report on the deployment of a prototype A-DTS flowmeter in a fractured rock aquifer. With this design, an increase in flow velocity from 0.01 to 0.3 m s−1 elicited a 2.5°C cooling effect. It is envisaged that with further development this method will have applications where point measurements of borehole vertical flow do not fully capture combined spatiotemporal dynamics.
28 October 2015 in Geoscientific Instrumentation, Methods and Data Systems
We develop an approach for measuring in-well fluid velocities using point electrical heating combined with spatially and temporally continuous temperature monitoring using distributed temperature sensing (DTS). The method uses a point heater to warm a discrete volume of water. The rate of advection of this plume, once the heating is stopped, equates to the average flow velocity in the well. We conducted thermal-plume fibre optic tracking (T-POT) tests in a borehole in a fractured rock aquifer with the heater at the same depth and multiple pumping rates. Tracking of the thermal plume peak allowed the spatially varying velocity to be estimated up to 50 m downstream from the heating point, depending on the pumping rate. The T-POT technique can be used to estimate the velocity throughout long intervals provided that thermal dilution due to inflows, dispersion, or cooling by conduction does not render the thermal pulse unresolvable with DTS. A complete flow log may be obtained by deploying the heater at multiple depths, or with multiple point heaters.
11 June 2015 in EGUsphere
We develop an approach for measuring in-well fluid velocities using point electrical heating combined with spatially and temporally continuous temperature monitoring using Distributed Temperature Sensing (DTS). The method uses a point heater to warm a discrete volume of water. The rate of advection of this plume, once the heating is stopped, equates to the average flow velocity in the well. We conducted Thermal-Plume fibre Optic Tracking (T-POT) tests in a borehole in a fractured rock aquifer with the heater at the same depth and multiple pumping rates. Tracking of the thermal plume peak allowed the spatially varying velocity to be estimated up to 50 m downstream from the heating point, depending on the pumping rate. The T-POT technique can be used to estimate the velocity throughout long intervals provided that thermal dilution due to inflows, dispersion, or cooling by conduction do not render the thermal pulse unresolvable with DTS. A complete flow log may be obtained by deploying the heater at multiple depths, or with multiple point heaters.