1 January 2021 in Trudy Universiteta
Целью работы является определение ширины целиков между камерами при отработке рудного месторождения выемочными камерами. Выработка состоит из штреков, пройденных под рудной панелью, и нескольких отработанных камер многоугольного сечения. Напряженное состояние вокруг полевой выработки определяется методом конечных элементов с применением программного комплекса ANSYS в двумерной постановке. Путем анализа напряженного состояния в целиках между камерами разработана методика определения расчетного напряжения в целике. Определены основные факторы, влияющие на напряженное состояние в целике и составлена матрица рационального планирования многофакторных компьютерных экспериментов. Путем проведения этих экспериментов и обработки результатов методом нетрадиционного регрессионного анализа получены аналитические зависимости для определения расчетного напряжения в наиболее нагруженном целике при сопряжении двух, трех и четырех камер. Обоснован коэффициент запаса, учитывающий скол стенки целиков и из расчетов на прочность получены выражения для определения ширины целиков между...
1 January 2026 in Journal of Applied Engineering Science
The aim of the study is to develop a methodology for calculating the dynamic characteristics of nonlinear vibration isolators and to evaluate the influence of the type of dissipative forces on the vibration protection efficiency. The paper addresses the calculation of vibration isolators with nonlinear elastic and dissipative properties under harmonic force and kinematic excitations. Using the harmonic linearization method, general expressions were derived for the amplitude-frequency response and the vibration isolation efficiency coefficient. The analysis of these expressions determined the conditions for suppressing large-amplitude vibrations. Specific analytical relationships were obtained for vibration isolators possessing the most common nonlinear elastic characteristics. These include isolators with odd cubic stiffness characteristics, preloaded systems, systems with symmetric linear elastic stops, and systems with a nonlinear elastic element and symmetric rigid stops. It was established that the efficiency of vibration protection systems depends significantly on the type of dissipative forces present in the isolator. Analytical relationships were derived, and the performance of vibration isolators with viscous, dry, and internal friction was analyzed. A comparison of the performance efficiency of vibration isolators with different dissipative characteristics was conducted. The possibility of achieving vibration protection goals by combining different forms of damping is highlighted.
17 April 2026 in Journal of Applied Engineering Science
The aim of the study is to develop a methodology for calculating the dynamic characteristics of nonlinear vibration isolators and to evaluate the influence of the type of dissipative forces on the vibration protection efficiency. The paper addresses the calculation of vibration isolators with nonlinear elastic and dissipative properties under harmonic force and kinematic excitations. Using the harmonic linearization method, general expressions were derived for the amplitude-frequency response and the vibration isolation efficiency coefficient. The analysis of these expressions determined the conditions for suppressing large-amplitude vibrations. Specific analytical relationships were obtained for vibration isolators possessing the most common nonlinear elastic characteristics. These include isolators with odd cubic stiffness characteristics, preloaded systems, systems with symmetric linear elastic stops, and systems with a nonlinear elastic element and symmetric rigid stops. It was established that the efficiency of vibration protection systems depends significantly on the type of dissipative forces present in the isolator. Analytical relationships were derived, and the performance of vibration isolators with viscous, dry, and internal friction was analyzed. A comparison of the performance efficiency of vibration isolators with different dissipative characteristics was conducted. The possibility of achieving vibration protection goals by combining different forms of damping is highlighted.
1 January 2025 in Journal of Applied Engineering Science
The paper presents an algorithm for calculating key statistical parameters, including correlation dependences, correlation coefficients, and a method of checking the presence of a linear dependence. A quadratic regression equation is obtained, regression curve graphs are constructed, distribution functions and probability densities with the procedure for their normalization are calculated. The main statistical parameters of random variables are also calculated: mathematical expectation, variance, standard deviation, and quantiles of various levels. The proposed regression analysis algorithm can be used to assess safety and reliability of building structures, which allows analyzing their operation in a probabilistic form. Based on the theoretical and applied results of the work, prospects are opened for further development of probabilistic analysis methods for safety of construction projects as a whole, taking into account their complex structure and interaction of various structural elements.
7 October 2025 in International Journal of Innovative Research and Scientific Studies
This study investigates the thermo-mechanical behaviour of titanium alloys during milling with the aim of developing a predictive approach for reducing thermal loading and improving process stability. A three-dimensional finite element model was constructed in Kompas-3D and simulated in ANSYS Workbench using the Johnson–Cook constitutive and damage model. To systematically analyse the effects of process variables, a five-level experimental design was employed, in which cutting depth, feed rate, and spindle speed were varied. The results of 25 simulation runs were processed in ANETR-5 software to establish a regression model linking cutting parameters with the workpiece surface temperature. The findings revealed that heat accumulation is strongly localised at the tool–chip interface, while subsurface temperature stabilises near 101.9 °C. Cutting forces were observed to fluctuate in all coordinate directions, reflecting the intermittent engagement of milling teeth and providing insight into potential process instability. The regression model demonstrated high adequacy with SD = 28.76%, R = 0.948, and F = 12.093. Optimisation indicated that the combination of cutting depth t = 1 mm, feed rate S = 4500 mm/min, and spindle speed n = 4162 rpm yields the most favourable thermal response. The approach provides a reliable basis for optimising titanium machining, improving tool life, surface integrity, and overall cost efficiency.