6 December 2013 in Science
Deep Drilling for Earthquake Clues: The 2011 M w 9.0 Tohoku-Oki earthquake and tsunami were remarkable in many regards, including the rupturing of shallow trench sediments with huge associated slip (see the Perspective by Wang and Kinoshita ). The Japan Trench Fast Drilling Project rapid response drilling expedition sought to sample and monitor the fault zone directly through a series of boreholes.
Chester
et al.
(p. 1208 ) describe the structure and composition of the thin fault zone, which is predominately comprised of weak clay-rich sediments. Using these same fault-zone materials,
Ujiie
et al.
(p. 1211 ) performed high-velocity frictional experiments to determine the physical controls on the large slip that occurred during the earthquake. Finally,
Fulton
et al.
(p. 1214 ) measured in situ temperature anomalies across the fault zone for 9 months, establishing a baseline for frictional resistance and stress during and following the earthquake.
6 June 2018 in Geophysical Research Letters
Episodic tremor and slow slip (ETS) occurs in the transition zone between the locked seismogenic zone and the deeper, stably sliding zone. Actual mechanisms of ETS are enigmatic, caused by lack of geological observations and limited spatial resolution of geophysical information from the ETS source. We report that quartz‐filled, crack‐seal shear and extension veins in subduction mélange record repeated low‐angle thrust‐sense frictional sliding and tensile fracturing at near‐lithostatic fluid pressures. Crack‐seal veins were coeval with viscous shear zones that accommodated deformation by pressure solution creep. The minimum time interval between thrusting events, determined from a kinetic model of quartz precipitation in shear veins, was less than a few years. This short recurrence time of low‐angle brittle thrusting at near‐lithostatic fluid overpressures within viscous shear zones may be explained by frequent release of accumulated strain by ETS.
29 December 2010 in Geophysical Research Letters
We conducted high‐velocity friction experiments on clay‐rich fault gouge taken from the megasplay fault zone in the Nankai subduction zone under dry and wet conditions. In the dry tests, dehydration of clay minerals occurred by frictional heating, and slip weakening is related to thermal pressurization associated with water vaporization, resulting in a random distribution of clay‐clast aggregates in the gouge matrix. In the wet tests, slip weakening is caused by pore‐fluid pressurization via shear‐enhanced compaction and frictional heating, and there is a very weak dependence of the steady‐state shear stress on the normal stress. The resulting microstructure reflects the grain size segregation in a granular‐fluid shear flow at high shear rates. These results suggest that earthquake rupture propagates easily through clay‐rich fault gouge by high‐velocity weakening, potentially leaving the microstructures resulting from the frictional heating or the flow sorting at high slip rates.
1 January 2014 in Progress in Earth and Planetary Science
Subduction earthquakes on plate-boundary megathrusts accommodate most of the global seismic moment release, frequently resulting in devastating damage by ground shaking and tsunamis. As many earthquakes occur in deep-sea regions, the dynamics of earthquake faulting in subduction zones is poorly understood. However, the Integrated Ocean Drilling Program (IODP) Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) and fault rock studies in accretionary prisms exhumed from source depths of subduction earthquakes have greatly improved our understanding of earthquake faulting in subduction zones. Here, we review key advances that have been made over the last decade in the studies of fault rocks and in laboratory experiments using fault zone materials, with a particular focus on the Nankai Trough subduction zone and its on-land analog, the Shimanto accretionary complex in Japan. New insights into earthquake faulting in subduction zones are summarized in terms of the following: (1) the occurrence of seismic slip along velocity-strengthening materials both at shallow and deep depths; (2) dynamic weakening of faults by melt lubrication and fluidization, and possible factors controlling coseismic deformation mechanisms; (3) fluid-rock interactions and mineralogical and geochemical changes during earthquakes; and (4) geological and experimental aspects of slow earthquakes.
29 May 2020 in Science Advances
Hydration allows subducting oceanic crust to be far weaker than previously recognized.
20 March 2020 in Journal of Geophysical Research: Solid Earth
Earthquakes are expected to nucleate within velocity‐weakening materials; however, at the updip limit of the subduction seismogenic zone, the principal lithologies exhibit velocity‐strengthening behavior. At an exhumed analogue for present‐day subduction at Nankai (the Mugi Mélange, Japan) two examples of paleoseismic features occur within altered basalts, suggesting that they may be velocity‐weakening. We shear altered basalt and shale matrix from the mélange in the triaxial saw cut configuration at in situ conditions of deformation (Pc = 120 MPa, T = 150 °C) for two pore fluid factors (λ = 0.36, 0.7). The shale matrix exhibits a coefficient of friction between 0.4 and 0.5, and velocity‐strengthening behavior. Altered basalt exhibits Byerlee friction and velocity‐weakening behavior. In most experiments deformation was partitioned into Riedel shears, which have a lower percentage of clasts, clast size distributions with higher fractal dimensions, and shape factors indicating rounder clasts compared to the matrix between Riedel shears. We hypothesize that earthquakes preferentially nucleate within altered basalt at the updip limit of the seismogenic zone. More complex forms of deformation (e.g., shallow very low frequency earthquakes) may occur by mixing velocity‐weakening altered basalt into the velocity‐strengthening shale matrix. In subduction zones where the matrix is composed of shale, this complex behavior is limited to shallow depths (T < ~250 °C), above the updip transition to velocity‐weakening behavior for the matrix. Altered basalt is a ubiquitous subducting material, and future studies on its behavior through a range of subduction zone conditions are required for a full understanding of the mechanical behavior of subduction zones.