State key laboratory of Information photonics and optical communications, School of Electronic Engineering, Beijing University of Posts and Telecommunications, Beijing 100876, China
Auto-generated profile, based on publicly available information
Xueliang Gu
State key laboratory of Information photonics and optical communications, School of Electronic Engineering, Beijing University of Posts and Telecommunications, Beijing 100876, China
Fiber Bragg grating (FBG) sensors are extensively employed for structural health and condition monitoring. However, the high cost and large size of conventional FBG demodulation methods have hindered the widespread adoption of FBG-based sensing technologies. To overcome these challenges, this study proposes what we believe to be a novel demodulation system leveraging a tunable laser. The system utilizes a gated recurrent unit (GRU) peak-finding algorithm, implemented on an STM32 microcontroller with edge AI capabilities, all integrated onto a compact 100×100×10 mm circuit board. This approach enables demodulation across the entire C-band, achieving a monitoring range of 70 km, a demodulation frequency of 100 Hz, and a mean absolute error (MAE) of 9.6 pm.
Optical frequency domain reflectometry (OFDR) is widely used in various fields. This paper presents an optimized wavelength selection matching (WSM) and local cross-correlation (LCC) technique for real-time strain monitoring based on OFDR. WSM is employed to extract waveform features and identify suspected strain locations. LCC is used to calculate the strain at these suspected locations to obtain accurate results. According to the results, with the optimized method, the strain localization error is below 0.02% in various situations. Meanwhile, the demodulation speed outperforms traditional algorithms in all aspects.
Despite advancements in optical fiber sensing and power transmission technologies, existing systems face challenges of redundant multi-device deployment and incoordination between power supply and communication under complex working conditions such as strong electromagnetic interference, hazardous areas, or long-distance monitoring. This paper proposes a passive-active hybrid fiber Bragg grating (FBG) fiber-powered system, integrating sensing, power supply, and communication functions through a single-fiber architecture. The system utilizes the reflected spectrum of the FBG for wavelength demodulation, harnesses the transmission spectrum to supply DC power to remote low-power sensors, and establishes a high-speed backhaul channel based on the low-loss transmission characteristics of the FBG at the 1310 nm wavelength. Experimental results demonstrate that the system simultaneously achieves FBG temperature sensing (sensitivity: 9.7 pm/°C), power supply to electronic temperature monitoring nodes, and 1.25 Gbps error-free communication (BER < 10−12) over a 20-km single-mode fiber. This provides an innovative solution for reliable monitoring in high-risk scenarios such as petrochemical plants and power grids.
Thermoelectric harvesting technology is a clean and friendly energy-conversion technology. In the π-type traditional thermoelectric module (TEM), n- and p-type thermoelectric legs are electrically connected in a series to generate large temperature differences in the heat flow direction and to achieve a better module performance. However, damages to one thermoelectric leg could lead to the failure of the thermoelectric system. This work proposes a novel forked-finger electrode-structured thermoelectric module (FFTEM), which enables a simultaneous parallel electrical connection and thermal transfer in a homogeneous material’s thermoelectric leg set. The four thermoelectric legs share a common pair of electrodes, and this parallel structure makes the FFTEM benefit from low internal resistance, a high operating current, and high output power. The internal resistance and output power of the TEM are 4.25 mΩ and 1.766 mW, respectively, at a temperature difference of 40 °C. The internal resistance of the FFTEM is reduced to 0.81 mΩ, and the output power is increased to 13.81 mW. The FFTEM’s maximum output power achieved under temperature-dependent conditions is nine times that of the TEM’s output power. This FFTEM design provides a configuration to obtain a much higher output power, which could benefit future applications of thermoelectric devices.
To enable mains-free wireless access in confined environments such as tunnels and mines, this paper proposes and experimentally demonstrates a converged power-over-fiber (PoF) and analog radio-over-fiber (A-RoF) system over a single standard single-mode fiber (SMF). Using wavelength-division multiplexing (WDM), the system employs 1310 nm/1330 nm channels for bidirectional RF transmission and a 1550 nm channel for optical power delivery, respectively, while an ultra-simplified remote unit (RU) with a steady-state power consumption of 0.37 W is designed to match the PoF power-delivery capability. Experimental results show that for back-to-back, 1 km and 2 km links, the A-RoF performance remains essentially unaffected, with error vector magnitude (EVM) remaining stable, as the delivered PoF optical power varies from 0 to 3 W. For the 2 km transmission case, an incident PoF optical power of 2 W at the photovoltaic power converter (PPC) is sufficient to sustain stable system operation for over 10 hours. Under these conditions, using an IEEE 802.11ax MCS-7 (64QAM ) waveform, the optimum operating point yields an EVM of approximately 0.7%, satisfying the MCS-7 modulation-quality requirement.
This paper proposes a reliability-optimized localization method for underground utility tunnels based on multi-source fusion and a denoising variational autoencoder model. The method acquires a multi-sensor localization dataset aligned with a unified time reference. By employing a convolutional neural network-assisted denoising variational autoencoder (DVAE-CNN), it regulates localization outcomes through three key aspects: a multi-source heterogeneous data quality assessment model, a formulation of the target state transition equation, and an environmental prior-information-aided weight update strategy. This approach overcomes the low-reliability issues caused by information loss and errors in the complex environment of underground utility tunnels. Compared to localization results without reliability regulation mechanisms, the proposed method achieves an average improvement of 73.6% in localization accuracy and 85.2% in localization reliability. Finally, localization experiments conducted in an underground utility tunnel demonstrate that the proposed method can provide highly robust, reliable and continuous positioning services, indicating significant potential for application and broader adoption.