Chengtun Qu

Chengtun Qu

Auto-generated profile, based on publicly available information

Chengtun Qu

State Key Laboratory of Petroleum Pollution Control, Xi’an Shiyou University, Xi’an, China

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 July 2017 in Bulletin of Chemical Reaction Engineering & Catalysis
Verified
Journal Article
Open access
PDF file
TYTao Yu
Tao Yu
CQChengtun Qu
Chengtun Qu
DFDaidi Fan
Daidi Fan
RXRenjun Xu
Renjun Xu
The adsorption capacity of bentonite clay for heavy metal removal from wastewater can be significantly enhanced by a high loading of chitosan on the surface. In order to enhance the chitosan loading, we tested activating bentonite clay by three methods prior to chitosan loading: sulfuric acid, calcination, and microwave treatments. Meanwhile, several parameters during chitosan loading, namely the initial chitosan concentration, stirring speed, reaction time, temperature, and pH value were investigated. Our results indicate that chitosan is attached to bentonite clay through intercalation and surface adsorption according to X-ray Diffraction (XRD), Scanning Eelectron Microscopy (SEM), and Fourier Transform Infrared Spectroscopy (FTIR) analyses. The maximum chitosan loading on 200-mesh raw bentonite clay (126.30 mg/L) was achieved under the following conditions: the initial chitosan concentration of 1000 mg/L, the stirring speed of 200 rpm, pH of 4.9, 60 min of reaction time, and temperature of 30 °C. The chitosan loading was further increased to 256.30, 233.70, and 208.83 mg/g, when using bentonite clay activated through 6 min of microwave irradiation (800 W), 10 % sulfuric acid treatment, and calcinations at 600 °C, respectively. When the chitosan loading was increased from 34.76 to 233.7 mg/g, the removal percentages of Cu(II), Cr(VI), and Pb(II) were improved, respectively from 78.90 to 95.5 %, from 82.22 to 98.74 %, from 60.09 to 86.18 %.

1 September 2022 in Petroleum Chemistry
Verified
Journal Article
Open access
PDF file
JDJie Dong
Jie Dong
SDSanbao Dong
Sanbao Dong
ZMZhipeng Miao
Zhipeng Miao
QWQingchen Wang
Qingchen Wang
YLYongfei Li
Yongfei Li
GCGang Chen
Gang Chen
In this study, the foaming properties of a compound surfactant formula containing cetyltrimethylammonium chloride (CTAC), cocamidopropyl betaine (CDAB), fatty alcohol polyoxyethylene ether-7 (AEO7) and sodium alpha-olefin sulfonate (AOST) were evaluated to meet the application requirements for foam generation and foam drainage in gas wells. The results exhibited that the foaming volume and the half-life of the compound surfactant solution (0.05 wt % CTAC + 0.7 wt % CDAB + 0.6 wt % AEO7 + 0.05 wt % AOST) can reach the values of 550 mL and 23 min, respectively, which suggested that the foaming ability and stability were improved in comparison with each solution containing a single surfactant. It showed that the surface tension can be lowered to 22.4 mN/m with the presence of the compound surfactants. Simultaneously, the microstructure of the foam was observed using a polarizing microscope, and it was found that there were almost no polyhedron structures in the foam within a certain range of formula concentrations. The results of the experiments also clarify that the formula has well properties of temperature resistance and salt resistance (measured using a high-speed agitator).

1 July 2021 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
TLTianle Liu
Tianle Liu
TYTao Yu
Tao Yu
GGGuoning Gao
Guoning Gao
XSxuan sun
xuan sun
FCFaguo Chong
Faguo Chong
CQChengtun Qu
Chengtun Qu
Supercritical water oxidation (SCWO) technology is efficient and offers significant development potential for hazardous waste treatment. The use of water in a supercritical state with special physical and chemical properties for refractory organic matter processing offers significant advantages. This article summarizes (i) the mechanism of SCWO technology and its research progress for oily sludge treatment; (ii) the effects of reaction temperature, pressure, residence time, oxygen ratio, catalyst, antioxidant, and other factors on oily sludge treatment; and (iii) problems in the current process. Finally, SCWO technology for the future development of oily sludge treatment is discussed.