Ryszard Szczepanik

Ryszard Szczepanik

Auto-generated profile, based on publicly available information

Ryszard Szczepanik

Air Force Institute of Technology

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 November 2015 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
KDKrzysztof Dominiczak
Krzysztof Dominiczak
Romuald RządkowskiRomuald Rządkowski
Romuald Rządkowski
WRWojciech Radulski
Wojciech Radulski
RSRyszard Szczepanik
Ryszard Szczepanik
Considered here are nonlinear autoregressive neural networks (NETs) with exogenous inputs (NARX) as a mathematical model of a steam turbine rotor used for the online prediction of turbine temperature and stress. In this paper, the online prediction is presented on the basis of one critical location in a high-pressure (HP) steam turbine rotor. In order to obtain NETs that will correspond to the temperature and stress the critical rotor location, a finite element (FE) rotor model was built. NETs trained using the FE rotor model not only have FEM accuracy but also include all nonlinearities considered in an FE model. Simultaneous NETs are algorithms which can be implemented in turbine controllers. This allows for the application of the NETs to control steam turbine stress in industrial power plants.

12 November 2018
Verified
Book Chapter
Closed access
PDF file
Romuald RządkowskiRomuald Rządkowski
Romuald Rządkowski
VGVitally Gnesin
Vitally Gnesin
LKLuba Kolodyazhnaya
Luba Kolodyazhnaya
RSRyszard Szczepanik
Ryszard Szczepanik

10 October 2018 in MATEC Web of Conferences
Verified
Journal Article
Open access
Romuald RządkowskiRomuald Rządkowski
Romuald Rządkowski
LKLeszek Kubitz
Leszek Kubitz
MMMichał Maziarz
Michał Maziarz
Pawel TrokaPawel Troka
Pawel Troka
LPLeszek Piechowski
Leszek Piechowski
RSRyszard Szczepanik
Ryszard Szczepanik
This paper presents the experimental and numerical studies of last stage LP mistuned steam turbine bladed discs during run-down. The natural frequencies and mode shapes of the turbine bladed disc were calculated using an FE model. The influence of shaft was considered. The tip-timing method was used to find the mistuned bladed disc modes and frequencies. The numerical results were compared with experimental ones.

1 December 2019 in Journal of KONES
Verified
Journal Article
Open access
PDF file
AKArkadusz Koprowski
Arkadusz Koprowski
DGDominik Gotowski
Dominik Gotowski
Romuald RządkowskiRomuald Rządkowski
Romuald Rządkowski
RSRyszard Szczepanik
Ryszard Szczepanik
The process of the design of the 1 MW steam turbine includes designing the stator and rotor blades, the steam turbine inlet and exit, the casing and the rotor. A turbine that operates at rotation speeds other than 3000 rpm requires a gearbox and generator with complex electronic software. This article analyses the efficiency of eight turbine variants, including seven inlet geometries and three stages of stator as well as an eight variant with one of the inlets, all three stages and an outlet. This article analyses the efficiency of 8 turbine variants, including four spiral inlet geometries and tree stages in a 1 MW steam turbine. In the article, inlets and 1st stator blades of various geometries were analysed to obtain maximal turbine efficiency. Changing the inlet spiral from one pipe to two pipes increased the turbine efficiency. The geometry of the blades and turbine inlets and outlet was carried out using Design Modeller. The blade mesh was prepared in TurboGrid and inlet in ANSYS Meshing.

1 January 2015
Verified
Book Chapter
Closed access
PDF file
Romuald RządkowskiRomuald Rządkowski
Romuald Rządkowski
EREdward Rokicki
Edward Rokicki
RSRyszard Szczepanik
Ryszard Szczepanik
JŻJózef Żurek
Józef Żurek

16 December 2019 in E3S Web of Conferences
Verified
Conference Paper
Open access
PDF file
AKArkadiusz Koprowski
Arkadiusz Koprowski
DGDominik Gotowski
Dominik Gotowski
RRRomuald Rządkowski
Romuald Rządkowski
RSRyszard Szczepanik
Ryszard Szczepanik
In small turbines, inlets can be designed using an inlet spiral. This paper analyses the efficiency of eight turbine variants, including seven with three stator and rotor blades and inlet spirals of various geometries, and one variant with a spiral, three stages and an outlet. This involves a 3D steady viscous flow using ANSYS CFX. The analysis shows that the spiral has a considerable influence on turbine efficiency.