23 March 2016 in Quality and Reliability Engineering International
This paper discusses the use of linear mixed models and generalized linear mixed models to predict the wear and damage trajectories of railway wheelsets for a fleet of modern multiple unit trains. The wear trajectory is described by the evolution of the wheel flange thickness, the flange height and the tread diameter, whereas the damage trajectory is assessed through the probabilities of various types of wheel tread damage such as rolling contact fatigue, wheel flats and cavities occurring. Different model specifications are compared based on an information criterion. Copyright © 2016 John Wiley & Sons, Ltd.
10 July 2018 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
This paper investigates the wear rate and pattern for wheels turned with thin flanges using economic tyre turning. Economic tyre turning refers to the process of turning wheels to a profile that has the same tread shape but a thinner flange than the design case profile, allowing less material to be removed from the wheel diameter during re-profiling. Modern wheel lathes are typically capable of turning such profiles but the GB railway group standards do not currently permit their use. The paper demonstrates how the wheel profile damage model (WPDM) can be used, with a good degree of accuracy, to predict both the magnitude of wheel wear and the worn profile shape of the design and economic tyre turning re-profiled wheels for service mileages exceeding 100,000 miles. The WPDM simulations were run for two typical electric multiple units (one suburban and one intercity train fleet) and a two-axle freight wagon. Additionally, it discusses the calibration methodology used to adjust the wear coefficients contained within the Archard wear model to improve the accuracy of the WPDM simulation results for specific routes and vehicle types. Furthermore, this paper presents the findings of a trial of economic tyre turning on a fleet of intercity trains. The analysis is extended to predict the effect of using economic tyre turning on rail rolling contact fatigue for typical routes and operating conditions using a series of vehicle dynamic simulations. The analysis considers new 56E1 and 60E2 rails together with a selection of worn wheel. The research provides valuable evidence to support a future change to the standards which will allow train operators/maintainers to implement economic tyre turning policies.
19 September 2018 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
This paper describes the current version of the Low Adhesion Braking Dynamic Optimisation for Rolling Stock (LABRADOR) simulation tool that can predict the train brake system performance and support decision-making in the design and optimisation of the braking system including wheel slide protection, sanders and the blending and control of friction and dynamic brakes in low adhesion conditions. The model has been developed in MATLAB/Simulink and is intended to mimic the braking performance of both older and newer generations of multiple unit passenger trains. LABRADOR models have been initially validated by comparing simulation results for a single car train (Class 153) and two-car train (Class 158) in dry conditions with experimental tests, for tare and crush laden vehicles. This project is supported by RSSB and a technical steering group composed of railway braking experts, suppliers and train operators and manufacturers.
1 June 2022 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
This paper investigates whether it is possible to develop a wheel profile design that will extend wheelset life compared to an existing commonly used Great Britain passenger wheel profile, the P8. The P8 wheel profile was originally developed in the late 1960s as an alternative to a 1:20 coned wheel profile (the P1). The P1 often required frequent turning as the conicity could increase quickly over time as the wheel wore in service. The P8 was designed based on an average worn shape of a P1 wheel. The P8 was found to stay closer to its original shape as it wore in service. However, new P8 wheels or newly profiled P8 wheels tend to experience a high initial flange wear rate in the first 20,000–30,000 miles, until the worn wheel shape reaches ‘dimensional stability’; after this, the flange width typically remains relatively constant. A ‘Reduced Flange Wear’ (RFW) wheel profile has been developed, based on the P8 profile but with a modified flange root geometry. The Wheel Profile Damage Model has been used to calculate how the proposed RFW wheel profile could reduce wear rates and therefore increase wheelset life. This paper presents results for a typical electric multiple unit train (EMU1) running on rural and suburban routes and a higher speed variant (EMU2) running on an inter-city route. The effect of the proposed RFW profile on rail rolling contact fatigue (RCF) has also been evaluated using the Whole Life Rail Model, for the same routes. The results suggest that the proposed RFW profile does reduce flange wear compared to a P8, with larger reductions achieved on routes that are more curvaceous. For wheel turning based purely on restoring wheel profile geometry, the RFW profile could half the amount of material removed at each turning (based on turning wheels at 250,000 miles). Furthermore, the results show that the RFW profile experiences slightly less wheel RCF damage than the P8. When new, the RFW profile appears to cause slightly higher rail RCF than a new P8 (For radii 700 m < R < 1300 m); however, the results suggest that worn RFW profiles cause very similar rail RCF to that caused by worn P8 wheels.
1 November 2016 in IET Intelligent Transport Systems
This study describes a novel technique for estimating the frequency with which trains approach signals showing a red aspect. This knowledge is potentially important for understanding the likelihood of a signal being passed at danger (SPAD) at individual signals and also for normalisation of SPAD data, both locally and nationally, for trending and benchmarking. The industry currently uses estimates for the number of red aspect approaches based on driver surveys which are considered to have significant shortcomings. Data for this analysis is sourced from publicly available live feeds provided by Network Rail which give information on train movements and signal states. The development of the analysis model and supporting software are described and some sample results from case studies are presented. An initial study of seven signalling areas showed that approximately 3.3% of all signal approaches are to red signals. However, it also highlighted that there is a large variation in the red approach rates between signalling areas and between individual signals. SPAD risk assessment at individual signals may be significantly enhanced by the ability to estimate red approach rates for individual signals using the techniques described.
1 December 2018 in Safety Science