13 November 2013 in Scientific Reports
Novel activated boron nitride (BN) as an effective adsorbent for pollutants in water and air has been reported in the present work. The activated BN was synthesized by a simple structure-directed method that enabled us to control the surface area, pore volume, crystal defects and surface groups. The obtained BN exhibits an super high surface area of 2078 m2/g, a large pore volume of 1.66 cm3/g and a special multimodal microporous/mesoporous structure located at ~ 1.3, ~ 2.7, and ~ 3.9 nm, respectively. More importantly, the novel activated BN exhibits an excellent adsorption performance for various metal ions (Cr3+, Co2+, Ni2+, Ce3+, Pb2+) and organic pollutants (tetracycline, methyl orange and congo red) in water, as well as volatile organic compounds (benzene) in air. The excellent reusability of the activated BN has also been confirmed. All the features render the activated BN a promising material suitable for environmental remediation.
22 March 2013 in Nanotechnology
We report on the synthesis of high-quality microporous/mesoporous BN material via a facile two-step approach. An extremely high surface area of 1687 m(2) g(-1) and a large pore volume of 0.99 cm(3) g(-1) have been observed in the synthesized BN porous whiskers. The formation of the porous structure was attributed to the group elimination of organic species in a BN precursor, melamine diborate molecular crystal. This elimination method maintained the ordered pore structure and numerous structural defects. The features including high surface area, pore volume and structural defects make the BN whiskers highly suitable for hydrogen storage and wastewater treatment applications. We demonstrate excellent hydrogen uptake capacity of the BN whiskers with high weight adsorption up to 5.6% at room temperature and at the relatively low pressure of 3 MPa. Furthermore, the BN whiskers also exhibit excellent adsorption capacity of methyl orange and copper ions, with the maximum removal capacity of 298.3 and 373 mg g(-1) at 298 K, respectively.
10 September 2012 in The Journal of Physical Chemistry C
6 March 2015 in Journal of Materials Chemistry A
Adsorption represents an efficient and economical approach for water purification and substantial research is being performed to develop effective sorbent materials. Porous boron nitride (BN) composed of light elements is considered as a promising candidate for pollution treatment due to its unique polarity of B–N bonds, high specific surface area, numerous structural defects, chemical stability, and oxidation resistance. However, the adsorption performance based on porous BN is hindered by either few activated sites or a low degree of crystallinity. In this work, we have developed a simple chemical method to activate pre-obtained well-crystallized porous BN fibers in acid solution. The successful chemical activation has been identified by FTIR spectra and zeta potential measurements. Benefiting from these advantageous features, the activated BN fibers with high stability exhibited enhanced cationic dye removal performance compared to the un-activated ones. The effects of pH value, contact time, temperature and adsorbent amount on the methylene blue (MB) adsorption properties were analyzed. The adsorption equilibrium data were interpreted in terms of Langmuir and Freundlich models and the results showed that Langmuir isotherms best represent the adsorption system. The maximum adsorbed amount for MB was as high as 392.2 mg g−1 at pH 8.0 and 30 °C. The adsorption rate was sharply enhanced after chemical activation. The excellent reusability of the activated BN was also confirmed. It is shown that chemical activation plays a key role in enhanced dye adsorption performance. Therefore, our developed chemical activation method for porous BN fibers opens the door toward the practical application of activated BN for drinking water purification.
18 December 2015 in RSC Advances
One-dimensional (1D) boron nitride (BN) nanostructures with a high aspect ratio are of prime interest due to their importance in fundamental research and wide-range potential applications. Herein we developed a facile method for the first synthesis of ultrafine porous BN nanofibers in high purity and a high yield. The method included two-steps, freeze-drying of a hot melamine/boric acid solution and post pyrolysis of the as-obtained products. The extremely rapid cooling of the hot melamine/boric acid solution during the freeze-drying process resulted in the formation of ultrafine precursors, which was the key for the final synthesis of porous BN nanofibers with downsized diameters (20–60 nm) and high aspect ratios. The as-synthesized ultrafine BN nanofibers possessed a high specific surface area and a large pore volume, which could be tuned by the pyrolysis parameters. All of these characteristics make the porous BN nanofibers promising in the applications of water treatment, hydrogen storage, catalyst support, etc. Especially, ultrafast adsorption of methylene blue (MB) in water has been demonstrated using the present porous BN nanofibers as an adsorbent.
1 July 2012 in Materials Letters