23 June 2021 in Natural Hazards
Climate change leads to sea level rise worldwide, as well as increases in the intensity and frequency of tropical cyclones (TCs). Storm surge induced by TC’s, together with spring tides, threatens to cause failure of flood defenses, resulting in massive flooding in low-lying coastal areas. However, limited research has been done on the combined effects of the increasing intensity of TCs and sea level rise on the characteristics of coastal flooding due to the failure of sea dikes. This paper investigates the spatial variation of coastal flooding due to the failure of sea dikes subject to past and future TC climatology and sea level rise, via a case study of a low-lying deltaic city- Shanghai, China. Using a hydrodynamic model and a spectral wave model, storm tide and wave parameters were calculated as input for an empirical model of overtopping discharge rate. The results show that the change of storm climatology together with relative sea level rise (RSLR) largely exacerbates the coastal hazard for Shanghai in the future, in which RSLR is likely to have a larger effect than the TC climatology change on future coastal flooding in Shanghai. In addition, the coastal flood hazard will increase to a large extent in terms of the flood water volume for each corresponding given return period. The approach developed in this paper can also be utilized to investigate future flood risk for other low-lying coastal regions.
1 July 2016 in Journal of Hydraulic Engineering
Two regimes can be distinguished for the pickup flux of sand. At a Shields parameter of less than about 0.5 (corresponding with flow velocities of 0.5–1 m/s), the erosion process is dominated by the size and density of the grains (grain by grain pickup). At higher flow velocities, the bulk properties of the sand bed start to influence the erosion process. Dilative behavior results in the inflow of water to the sand bed, which reduces the pickup flux (dilatancy-reduced pickup) because of the shearing of layers of sand. A pickup function was recently developed for this regime, incorporating the effect of bulk properties, such as permeability and porosity, on the pickup. This function agrees well with data of previous erosion experiments in which the permeability and porosity of the sand bed were varied. However, these experiments just met the condition for dilatancy-reduced pickup. The flow velocity during these previous experiments was between 1 and 1.5 m/s, while the Shields parameter varied bet...
30 June 2008 in Coastal Engineering
1 September 2016 in Maritime Engineering
Dikes constructed from sand generally have a sand core and clay layers on the slopes and the crest to protect the core against erosion. In extreme hydraulic conditions, several failure mechanisms can lead to destruction of the clay layers, exposing the sand core to water. When water overtops the dike and the protective cover of the land-side slope or the crest fails, water flows over the core and erodes the sand. The dike starts to breach, and eventually the land behind the dike is flooded. The rate at which the dimensions of the breach grow influences the rate of inundation of the polder. Reduction of the inundation rate may be achieved by retarding the breaching process. This may reduce the number of casualties, resulting in increasing safety for the inhabitants. In order to achieve, for instance, a safety level ten times higher, mortality has to decrease by a factor of 10. The breaching process can be retarded by reducing the erosion velocity of the sand core. Experiments were executed to investigate the effect on the erosion velocity of adding bentonite to sand. The results of these experiments showed a significant reduction of the permeability and erosion velocity of the sand–bentonite mixtures compared with those of pure sand. The effect of adding bentonite on the breaching process was investigated by applying the Bres model (breach erosion in sand dikes model) to a sand dike tested in a large-scale field experiment (Zwin'94). It was found that adding a small percentage of bentonite reduces the rate of breach growth and the inundation rate in the polder. For the Zwin’94 dike it was determined that 5·4% of bentonite is sufficient to reduce the inundation rate below a threshold value of 0·5 m/h, leading to a significant increase in safety.
30 April 2025 in Journal of Coastal and Hydraulic Structures
Coastal and fluvial flood defences currently rely primarily on existing (grey) infrastructure such as dikes. However, coastal flood risk is expected to increase substantially in the near future. This requires ever increasing efforts to strengthen dikes. To aid these conventional methods, Nature-based Solutions (NbS) are increasingly proposed, such as coastal wetlands. Coastal wetlands have many ecological benefits, but also aid flood protection, especially tidal marshes. Tidal marshes protect the dikes behind them through wave attenuation and reduce flood damage if the dike is breached. Meanwhile, flood risk assessment relies on dike breach modelling to estimate the breach discharges for inundation simulations. Yet, how these foreshores (e.g., tidal marsh) affect dike breach development is largely unknown. For this reason, we experimentally explore how different foreshores affect the dike breaching process. In this study we performed a series of breach tests with a 1.5-1.9 m high model sand-dike with and without a foreshore. We tested two types of foreshores, an erodible sand and low-erodible clay layer, acting as proxies for a sandy beach and unvegetated tidal marsh. Because dike breach flow closely resembles weir flow, the standard weir equation applies, which is also frequently used in breach discharge models. The observed foreshore effects are qualitatively evaluated using this weir equation. Depending on foreshore stability, we find that foreshores affect breach hydrodynamics which alters the weir shape, leading to reduced breach width growth and ultimately limits the specific discharge.