27 September 2019 in IEEE Transactions on Microwave Theory and Techniques
This article presents a fully integrated modular wideband frequency interleaving (FI) transmitter and receiver for high data rate communication applications. At the transmitter side, three independent in-phase and quadrature-phase (IQ) baseband channels are upconverted to different intermediate frequencies (IFs) and then interleaved. At the receiver side, the interleaved signals are downconverted and separated back to each independent channel. Single-ended inputs and outputs are utilized to reduce the pin count, for a more practical realization and higher potential toward future system scaling. Special design techniques are followed to minimize crosstalk and intermodulation products between the channels. All circuits are manufactured and measured in a 130-nm SiGe:C BiCMOS technology with fT,/,fmax,=,300/500 GHz. The FI transmitter achieves a channel bandwidth of 2.5 GHz with less than 3-dB difference across different channels until 15-GHz IF. It consumes 560 mW from 2.5 and 3.3 V supplies and occupies a silicon area of 1.9 mm². The FI receiver achieves a baseband channel bandwidth of 2.5 GHz with a 1-dB difference between the channels until the same IF. It consumes 860 mW from 2.5 and 3.3 V supplies and has a chip area of 1.55 mm². The circuits are deployed in a communication experiment; first, in a back-to-back test with a direct cable connection, demonstrating a data rate of 15.6 Gb/s across the three IQ channels with a 16-QAM modulation scheme and a worst case transmitter-to-receiver error vector magnitude (EVM) of -18.6 dB. Then, a wireless experiment is performed with a 240-GHz front end with on-chip antenna, demonstrating a data rate of 7.8 Gb/s with QPSK modulation and a worst case EVM of -8.3 dB, across a wireless link of 15 cm. To the best of our knowledge, this is the first article that demonstrates a wireless transmission at sub-terahertz (sub-THz) carrier frequencies utilizing FI architectures.
14 January 2022 in IEEE Access
In past years, Parallel Sequence Spread Spectrum (PSSS) has attracted significant attention as a modulation technique for wireless communication systems targeting data rates of 100 Gb/s and beyond. PSSS allows designing high-speed baseband processors, which can be partially implemented in the analog domain. It uses multiple analog-to-digital converters (ADCs) to sample the received baseband signal in parallel, significantly relaxing the sampling rate and ADC complexity. However, due to the sidelobe effects of bipolar $m$ -sequences, PSSS shows lower performance than standard digital modulation schemes. This paper proposes real-valued PSSS spreading sequences with attenuated autocorrelation sidelobes. Such sequences show excellent bit error rate (BER) performance. Moreover, our sequences do not have length restrictions of 2 m – 1, like in the case of $m$ -sequences, and reduce the chip area required to implement PSSS transceiver. The proposed sequences also reduce the peak-to-average power ratio (PAPR) of PSSS.
7 January 2022 in IEEE Access
The key computation in the min-sum decoding algorithm of a Low-Density Parity-Check (LDPC) is finding the first two minima and also the location of the first minimum among a set of messages passed from Variable Nodes (VNs) to Check Nodes (CNs) in a Tanner graph. In this paper, we propose a modified rejection-based scheme for this task which is able to find the one-hot sequence of the minimum location instead of its index. We show that this modification effectively reduces the complexity of min-sum decoding algorithm. Additionally, we reveal a pipelining potential in such a rejection-based architecture which facilitates the multi-frame decoding of Low-Density Parity-Check (LDPC) codes and therefore results in an improvement in decoding throughput with bearable hardware overhead. Synthesis and floorplanning in an industrial 28 nm CMOS technology show improved results in terms of throughput, power, and chip area.