University of Belgrade, Institute of Chemistry, Technology and Metallurgy, Department of Electrochemistry, Belgrade, Serbia + University of Belgrade, Institute of Chemistry, Technology and Metallurgy, Center of Excellence in Environmental Chemistry and Engineering, Belgrade, Serbia
Auto-generated profile, based on publicly available information
Katarina Đ. Božić
University of Belgrade, Institute of Chemistry, Technology and Metallurgy, Department of Electrochemistry, Belgrade, Serbia + University of Belgrade, Institute of Chemistry, Technology and Metallurgy, Center of Excellence in Environmental Chemistry and Engineering, Belgrade, Serbia
This paper is focused on the preparation procedures, using a talc-based filler, to improve the rheologic properties of the lost foam refractory coatings. Talc, with grain size of 40 ?m, was mechanically activated in a vibration mill over the following times: 10, 20 and 30 min. Depending on the time required for the mechanical activation, the change in the filler grain size and shape was analysed along their effects on the talc-filled lost foam coating dispersion ability and stability. In order to characterize the filler, the following methods were used: X-ray diffraction, scanning electron microscopy and optic microscopy. The coating composition was tuned by choosing the suitable grain size and shape factor of the activated filler. In addition, different coating components (additives, solvent) were applied to alter the coating generation procedure. It was shown that the application of this type of the lost foam refractory coatings ? water-based coatings ? have a positive influence on quality of the aluminium alloy castings, which contributes to reducing the cost of cleaning and processing of the castings. Also, alcohol-based refractory coatings with talc-based activated fillers were tested and used to have the castings produced in the sand moulds.
Electrophoretic deposition (EPD) occurs as a cataphoretic deposition ? the coating is deposited on the cathode, and anaphoretic deposition ? the coating is deposited on the anode. The primary purpose of EPD is to obtain compact and uniform organic/inorganic coatings of the desired thickness and adhesion on metal surfaces by applying an electric field to the particles of coating precursor. EPD basic principles for coatings deposition concerning fundamental explanations and considerations of practical parameters of the process are presented. Cataphoretic deposition has become popular because it can apply organic coatings to complex structures that are otherwise very difficult to coat. These coatings were found to improve the characteristics of the substrate, such as biocompatibility, appearance and resistance to the corrosion processes. The key EPD parameters are composition, pH value and viscosity of deposition medium, as well as zeta potential of the particles, electric field strength, etc. A special survey is given to the process of anaphoretic deposition, which is relatively new, and its advantages over cataphoretic deposition are discussed. Through the process of joint anaphoresis/substrate anodization process, the surface of the substrate is simultaneously anodized and modified by incorporation of the foreign particles into the anodic layer. The coatings of mixed composition of better adhesion and corrosion resistance with respect to cataphoretically- deposited coatings are obtained as result.
1 January 2021 in Journal of the Serbian Chemical Society
This paper is focused on the preparation procedures, using talc-based filler to improve the rheologic properties of the lost foam refractory coatings. Talc, with grain size of 40 mm, was mechanically activated in a vibration mill over the following times: 10, 20 and 30 min. Depending on the time required for the mechanical activation, the change in the filler grain size and shape was analysed along their effects on the talc-filled lost foam coating dispersion ability and stability. In order to characterize the filler, the following methods were used: X-ray diffraction, scanning electron microscopy and optic microscopy. The coating compo-sition was tuned by choosing the suitable grain size and shape factor of the activated filler. In addition, different coating components (additives, solvent) were applied to alter the coating generation procedure. It was shown that the application of this type of the lost foam refractory coatings - water-based coatings - have a positive influence on quality of the aluminium alloy castings, which contributes to reducing the cost of cleaning and processing of the castings. Also, alcohol-based refractory coatings with talc-based activated fillers were tested and used to have the castings produced in the sand moulds.