Formation of semiconductor calcium silicide Ca2Si on Si(111)7×7 and 2/3√3-Mg surface phases and bulk Mg2Si film was studied. Conditions of high quality Ca2Si film growth were found. Formation of Ca surface phase was demonstrated at the initial stage of Ca2Si film growth on 2/3√3-Mg surface phase at narrow temperature range. Band gap of this surface phase and 2/3√3-Mg were obtained
BaSi2 thin films were formed on Si (111) substrate by solid-phase epitaxy (SPE) (UHV deposition) using the template technology followed by vacuum annealing at temperatures of 600 °C and 750 °C. After the deposition and annealing barium silicide films were characterized by Auger electron spectroscopy, grazing incidence x-ray diffraction (GIXRD) and atomic-force microscopy (AFM). It was established that the films annealed at T = 600 °C are polycrystalline with the structure of the orthorhombic BaSi2, with grain sizes of 100-200 nm. Higher anneal temperature (T=750 °C) leads to increase of diffraction peak intensity of BaSi2 phase with grain coagulation into 300-400 nm islands. It was confirmed that nanocrystalline BaSi2 films are characterized by a direct fundamental interband transition at 1.3 eV, the second interband transition with an energy of 2.0 eV, own phonon structure with wave number peaks at 112, 119, 146 and 208 cm-1 and a high density of defect states within the band gap, which provide a noticeable subband absorption at energies of 0.8 – 1.1 eV.
5 October 2009 in Journal of Physics: Condensed Matter
Electrical and optical properties of thin iron layers grown at room temperature on the epitaxial silicide Si(111)-(2 × 2)-Fe phase and on an Si(111)7 × 7 surface were investigated using in situ Hall effect registration, atomic force microscopy, and optical spectroscopy. It was established that Si(111)-(2 × 2)-Fe phase has semiconducting properties with a 0.99 eV effective band gap and acts as a diffusion barrier for the deposited iron atoms, preventing intermixing with the substrate at room temperature. Peculiarities in the optical spectra of a sample with a 2 nm iron film grown on the Si(111)-(2 × 2)-Fe phase typical for both metal and semiconducting natures prove a conservation of the phase under the iron layer. The process of iron growth on the Si(111)-(2 × 2)-Fe phase is accompanied by the development of high stress in the subsurface area resulting in band dispersion changes. Apparently the tension reaches a maximum at an iron layer thickness of 1.35 nm, and a high effective hole mobility equal to 820 cm(2) V(-1) s(-1) was registered.
The search for inexpensive and efficient methods of forming thin BaSi2 films as a promising material for photovoltaic is an actual task. The co-deposition of Ba and Si atoms with alloy thickness of 100-120 nm on the silicon substrate at room temperature with following annealing (SPE method) was proposed. Ba-Si alloy compounds then were thermally annealed at different temperatures and three samples were formed: #1 at T = 600 ° C, #2 at T = 700 ° C and #3 at T = 800 ° C. Polycrystalline films with an orthorhombic BaSi2 structure were formed by XRD, UV-VIS, FIR and Raman spectroscopies data. BaSi2 grains in samples #1 and #2 have sizes 62-64 nm and 86 nm in the sample #3 from XRD data calculations by Scherrer formula. Proposed growth method resulted to strong compression of the BaSi2 unit cell volume on 1.78 – 2.70%. The strongest compression was observed after annealing at 800 °C, which was accompanied by desorption of a noticeable amount of barium and a strong decrease in the film thickness in the sample #3. The formation of nanosize Si clusters was confirmed by Raman data for samples #2 and #3, but they did not observed in the sample #3. So, the film, formed at 800 °C, is the most qualitative in terms of structure and single-phase BaSi2, but with strong decrease of initial Ba-Si alloy thickness due to Ba desorption.
1 June 2019 in Journal of Physics: Conference Series
Polycrystalline and oriented films of barium disilicide (BaSi2) with a thickness of up to 100 nm were formed on silicon (111) substrates by high-temperature (800 ° C) solid-phase (single-stage and two-stage) annealing. The single phase of barium disilicide films and their semiconductor nature have been proven to be below 1.25 eV according to X-ray and optical spectroscopic methods. Two preferential orientations of the BaSi2 crystallites were detected and their orientation was determined in the films formed by two-stage annealing. According to the calculations of the parameters of the crystal structure of BaSi2 films, a compression of the unit cell volume from 2.7% to 5.13% was found, depending on the cooling time to room temperature. The stability of the films to laser radiation was studied by registering the Raman spectra with a variable power of laser radiation. The maximum power density of the laser beam (3⋅109 W/m2), which does not lead to the beginning of the destruction of these films, was determined.