Monojit Dutta

Monojit Dutta

Auto-generated profile, based on publicly available information

Monojit Dutta

TATA Steel Limited

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 January 2016 in Surface and Coatings Technology
Verified
Journal Article
Closed access
ACAnindita Chakraborty
Anindita Chakraborty
AMAvik Mondal
Avik Mondal
SBSandip Bysakh
Sandip Bysakh
MDMonojit Dutta
Monojit Dutta
SSShiv Brat Singh
Shiv Brat Singh

1 September 2014 in Applied Surface Science
Verified
Journal Article
Closed access
ABAtanu Banerjee
Atanu Banerjee
MDMonojit Dutta
Monojit Dutta
SBSandip Bysakh
Sandip Bysakh
ABAnil K. Bhowmick
Anil K. Bhowmick
TLTapas Laha
Tapas Laha

5 February 2014 in Journal of Adhesion Science and Technology
Verified
Journal Article
Closed access
ABAtanu Banerjee
Atanu Banerjee
MDMonojit Dutta
Monojit Dutta
SBSandip Bysakh
Sandip Bysakh
ABAnil K. Bhowmick
Anil K. Bhowmick
TLTapas Laha
Tapas Laha
Cu–Sn coatings with varying Sn content were deposited on steel substrate by immersion route and the effect of variation of Sn content and the substrate roughness on the interfacial adhesion strength of Cu–Sn-coated steel substrates vulcanized with styrene butadiene rubber were investigated. The surface roughness of the coatings did not vary compared to pristine steel substrate with change in Sn weight% in the coatings. The coated surfaces exhibited bare spots or deep trough as micro-discontinuities in the coatings, where formation of Fe2O3 was evident from SEM-EDS, AES, and XPS analysis. Microstructural study of the coating cross-section and coating-substrate interface by transmission electron microscopy of cross-sectioned samples revealed inadequate penetration of coating inside these troughs. Peel test carried out on the Cu–Sn-coated steel–rubber joints showed mixed mode i.e. adhesive and cohesive mode of interfacial fracture irrespective of the coating composition. The peel test further indicated higher interfacial adhesion strength for Cu–Sn-coated samples than pure Cu-coated samples, with an optimum adhesion strength for the coatings containing 3–4 wt.% Sn.

4 September 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Mohua SinhababuMohua Sinhababu
Mohua Sinhababu
ANURAG ROYANURAG ROY
ANURAG ROY
NKNarendra Kumar
Narendra Kumar
MDMonojit Dutta
Monojit Dutta
Senthilarasu SundaramSenthilarasu Sundaram
Senthilarasu Sundaram
GUGopalkrishnan Udayabhanu
Gopalkrishnan Udayabhanu
Pigments can retain their color for many centuries and can withstand the effects of light and weather. The paint industry suffers from issues like aggressive moisture, corrosion, and further environmental contamination of the pigment materials. Low-cost, long-lasting, and large-scale pigments are highly desirable to protect against the challenges of contamination that exist in the paint industry. This exploratory study reinforces the color and thermal stability of industrial-grade (IG) magnetite (Fe3O4). IG Fe3O4 pigments were further considered for surface treatment with sodium hexametaphosphate (SHMP). This metaphosphate hexamer sequestrant provides good dispersion ability and a high surface energy giving thermal and dust protection to the pigment. Various physicochemical characterizations were employed to understand the effectiveness of this treatment across various temperatures (180–300 °C). The X-ray diffraction, Raman, and X-ray photoelectron spectroscopy techniques signify that the SHMP-treated Fe3O4 acquired magnetite phase stability up to 300 °C. In addition, the delta-E color difference method was also adopted to measure the effective pigment properties, where the delta-E value significantly decreased from 8.77 to 0.84 once treated with SHMP at 300 °C. The distinct color retention at 300 °C and the improved dispersion properties of surface-treated Fe3O4 positions this pigment as a robust candidate for high-temperature paint and coating applications. This study further encompasses an effort to design low-cost, large-scale, and thermally stable pigments that can protect against UV-rays, dust, corrosion, and other color contaminants that are endured by building paints.