Pengming Jiang

Pengming Jiang

Auto-generated profile, based on publicly available information

Pengming Jiang

School of Architecture and Civil Engineering, Jiangsu University of Science and Technology, Zhenjiang, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 September 2021 in Environmental Earth Sciences
Verified
Journal Article
Closed access
PDF file
Xianwen HuangXianwen Huang
Xianwen Huang
Zhishu YaoZhishu Yao
Zhishu Yao
Wei WangWei Wang
Wei Wang
Aizhao ZhouAizhao Zhou
Aizhao Zhou
PJPengming Jiang
Pengming Jiang

8 April 2020 in Symmetry
Verified
Journal Article
Open access
PDF file
Aizhao ZhouAizhao Zhou
Aizhao Zhou
Xianwen HuangXianwen Huang
Xianwen Huang
NLNa Li
Na Li
PJPengming Jiang
Pengming Jiang
Wei WangWei Wang
Wei Wang
A soil–rock slope is a heterogeneous slope composed of soil and rocks that is widely distributed throughout the world. In order to accurately analyze the slope stability of soil–rock mixture, based on a Monte Carlo algorithm (fuzzy-based method), a symmetrical stability analyzing method for soil–rock slopes is proposed, considering the dispersion of strength of soil–rock mixtures. In analyzing it, the numerical model is symmetrical to the real soil–rock slope in geometry and material properties. In addition, the effect of rock content to slope stability was studied by this symmetrical method. The specific work of this paper is as follows: (1) The acquisition method of random number series for the Monte Carlo algorithm and the method of slope stability analysis, using the Monte Carlo method, are introduced. (2) According to in situ samples and remade samples, the strength characteristics of soil–rock mixtures were measured with different rock contents, which proved the scatter of strength of soil–rock mixtures. (3) Based on the measured strength parameters of soil–rock mixtures and the slope landslide, the reliability in analyzing results and superiority in calculating time of using the Monte Carlo method to analyze stability of soil–rock slopes are detailed. (4) The stability of soil–rock slopes with different rock content is discussed with the Monte Carlo method, and it is concluded that with the increase of rock content, the stability of a soil–rock slope decreases first and then increases, and the minimum safety factor is acquired at 20% rock content. (5) Based on a large number of calculation examples, the applied situations of the Monte Carlo method to analyze stability of soil–rock slopes are detailed according to sampling results and rock size.

16 March 2021 in Sustainability
Verified
Journal Article
Open access
PDF file
Aizhao ZhouAizhao Zhou
Aizhao Zhou
Xianwen HuangXianwen Huang
Xianwen Huang
Wei WangWei Wang
Wei Wang
PJPengming Jiang
Pengming Jiang
LXLI xinwei
LI xinwei
For reducing the initial GSHP investment, the heat transfer efficiency of the borehole heat exchange (BHE) system can be enhanced to reduce the number or depth of drilling. This paper proposes a novel and simple BHE design by changing the cross-sectional shape of the U-tube to increase the heat transfer efficiency of BHEs. Specifically, in this study, we (1) verified the reliability of the three-dimensional numerical model based on the thermal response test (TRT) and (2) compared the inlet and outlet temperatures of the different U-tubes at 48 h under the premise of constant leg distance and fluid area. Referent to the circular tube, the increases in the heat exchange efficiencies of the curved oval tube, flat oval tube, semicircle tube, and sector tube were 13.0%, 19.1%, 9.4%, and 14.8%, respectively. (3) The heat flux heterogeneity of the tubes on the inlet and outlet sides of the BHE, in decreasing order, is flat oval, semicircle, curved oval, sector, and circle shapes. (4) The temperature heterogeneity of the borehole wall in the BHE in decreasing order is circle, sector, curved oval, flat oval, and semicircle shapes. (5) Under the premise of maximum leg distance, referent to the heat resistance of the tube with a circle shape at 48 h, the heat exchange efficiency of the curved oval, flat oval, semicircle, and sector tubes increased 12.6%, 17.7%, 10.3%, and 7.8%, respectively. (6) We found that the adjustments of the leg distance and the tube shape affect the heat resistance by about 25% and 12%, respectively. (7) The flat-oval-shaped tube at the maximum leg distance was found to be the best tube design for BHEs.

1 February 2020 in International Journal of Geomechanics
Verified
Journal Article
Closed access
CLChengchao Li
Chengchao Li
PJPengming Jiang
Pengming Jiang
For some two-layered slopes subjected to the surcharge load, the soil mass undergoes rotational or translational movement. Thus, the conventional failure mechanism of homogeneous slopes is no longer applicable. To overcome the difficulty in stability assessment of two-layered slopes, a rotational-translational failure mechanism is proposed, and it is composed of rigid blocks rotating around the center point or sliding along the layered boundary. Meanwhile, two rotational failure mechanisms (face and base failures) are modified to evaluate the stability of two-layered slopes with upper bound limit analysis. Case studies and stability charts are carried out on two-layered slopes with various surcharge loads, slope geometries, and soil strengths. The results are useful to address advantages and application differences of the three failure mechanisms in engineering practice. In addition, the comparison with the Spencer method indicates that the upper bound solution of the rotational or rotational-translational mechanism in different conditions is more rigorous because of the lower factor of safety and the more reasonable slip surface.

21 February 2020 in Sustainability
Verified
Journal Article
Open access
PDF file
Xianwen HuangXianwen Huang
Xianwen Huang
Aizhao ZhouAizhao Zhou
Aizhao Zhou
Wei WangWei Wang
Wei Wang
PJPengming Jiang
Pengming Jiang
In order to support the dynamic design of subgrade filling engineering, an experiment on the dynamic shear modulus (G) and damping ratio (D) of clay–gravel mixtures (CGMs) was carried out. Forty-two groups of resonant column tests were conducted to explore the effects of gravel content (0%, 10%, 20%, 30%, 40%, 50%, and 60%, which was the mass ratio of gravel to clay), gravel shape (round and angular gravels), and confining pressure (100, 200, and 300 kPa) on the dynamic shear modulus, and damping ratio of CGMs under the same compacting power. The test results showed that, with the increase of gravel content, the maximum dynamic shear modulus of CGMs increases, the referent shear strain increases linearly, and the minimum and maximum damping ratios decrease gradually. In CGMs with round gravels, the maximum dynamic shear modulus and the maximum damping ratio are greater, and the referent shear strain and the minimum damping ratio are smaller, compared to those with angular gravels. With the increase of confining pressure, the maximum dynamic shear modulus and the referent shear strain increase nonlinearly, while the minimum and maximum damping ratios decrease nonlinearly. The predicting equation for the dynamic shear modulus and the damping ratio of CGMs when considering confining pressure, gravel content, and shape was established. The results of this research may put forward a solid foundation for engineering design considering low-strain-level mechanical performance.

1 January 2020 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
Xianwen HuangXianwen Huang
Xianwen Huang
Zhishu YaoZhishu Yao
Zhishu Yao
WBWang Bing-Hui
Wang Bing-Hui
Aizhao ZhouAizhao Zhou
Aizhao Zhou
PJPeng-Ming Jiang
Peng-Ming Jiang
Soil‐rock slopes are widely distributed in central or western China. With the development of transportation, many subgrades are being built on mountainsides and therefore, slope stability has to be estimated under high loadings. To obtain better estimation results, a new rock contour establishing algorithm was developed, capable of considering interlock effect between rocks. Then, computed tomography (CT) and unconfined triaxial tests with ring top loadings were conducted. Based on rock distribution characteristics (obtained by CT photos) and the appearance of shear failure surfaces in slopes under ring top loadings, four rock skeleton status and five shear failure surface developing models were introduced. Based on the developed rock contour establishing algorithm, ten groups (twelve models per group) were established and calculated by finite element method (FEM). After this, normalized ultimate loading increasing multiple N, which was the ultimate loading ratio of rock‐containing slope to uniform soil slope, was introduced to evaluate the influence of rock distributions on slope stability. The value of N was increased with the increase of rock content due to rock skeleton status. The values of N in slopes with angular rocks were about three times higher than those with round rocks which was due to complex geometric shape and distribution characteristics of angular rocks. Then, considering different slope angles (50°–60°), rock contents (0%–60%), and rock shapes (round and angular), the ultimate loading increasing multiple N of soil‐rock slopes under high loadings was calculated and suggested for engineering designs. Finally, based on the failure surfaces of numerical modes, three typical failure modes were developed, which could be reference for designers to deal with slopes.