Manjuan Yang

Manjuan Yang

Auto-generated profile, based on publicly available information

Manjuan Yang

Research Institute of Highway

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 July 2009
Verified
Conference Paper
Closed access
CJChengwu Jiao
Chengwu Jiao
MYManjuan Yang
Manjuan Yang
YHYubo Hao
Yubo Hao
There is a phenomenon of traffic accident migration in the highways after used for some period, especially those that have been improved for traffic safety. In order to make sure the hypostasis and causes of the phenomenon, the character of this phenomenon was analyzed and induced, based on the investigation of traffic accident data of 5 years occurring in a freeway in South China. Then the possible causes of traffic accident migration were researched. And some potential causes of traffic accident migration was analyzed by studying accident causes and analyzing the variation of infrastructure and safety measurements of the freeway.

20 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
FLFangfang Liu
Fangfang Liu
XCXiaowei Cheng
Xiaowei Cheng
YLYi Li
Yi Li
MYManjuan Yang
Manjuan Yang
YZYujing Zhou
Yujing Zhou
Accurately considering the dynamic mechanical properties of rolled thin-walled steel plates (TWSPs) under low and medium strain rates is the basis of numerical simulations of W-beam guardrails subjected to vehicle impact. Uniaxial tensile tests were conducted on specimens extracted from different locations (flat TWSPs without cold rolling treatment, and the cross-sectional centers and slopes of rolled TWSPs) and under different strain rates (ε˙ = 0.00025, 0.01, and 50 s−1). Based on experimental and numerical results, the cross-sectional center of a rolled TWSP is recommended as the representative sampling location for uniaxial tensile tests. Additional uniaxial tensile tests with wider strain rates of 10, 100, and 200 s−1 were also conducted on specimens at the recommended sampling location (cross-sectional center) of rolled TWSPs. It was found that the Cowper–Symonds model with parameters of C = 40 s−1 and p = 5 recommend by Symonds significantly overestimated the strain rate effects of the rolled TWSP material in the low and medium strain-rate region. The model with calibrated parameters of C = 4814 s−1 and p = 2.9 was recommended for considering the influences of strain rate effects on the dynamic mechanical properties of rolled TWSP at low to medium strain rates.

9 October 2013
Verified
Conference Paper
Closed access
MYManjuan Yang
Manjuan Yang
HZHongsong Zhang
Hongsong Zhang
Two reconstructed guardrail systems are developed to enhance the crashworthiness of in-service W-beam barriers installed on freeways. The interaction mechanism of vehicle and barriers in the collision process is simulated based on finite element method, and the simulation results are examined by safety performance evaluation criteria. Simulation results show that the three-beam system is successfully crash tested to grade-A conditions with 160kJ kinetic energy. The double W-beam system passes the grade-SB test while the kinetic energy is 280kJ. In all tests, vehicles don't penetrate, under-ride, or over-ride the test barriers after collisions and occupant ride-down accelerations of test cars are all less than 20g, which satisfies the evaluation criteria limits. In the two reconstructed guardrail systems, most of components in the original W-beam barriers could be reused. Compared with installing new barriers of the same test level, applying the two reconstructed guardrail systems can obviously reduce construction cost and decrease traffic influence.

2 September 2026
Verified
Book Chapter
Closed access
PDF file
SWShuai Wang
Shuai Wang
APAihui Pei
Aihui Pei
XFXiao Feng
Xiao Feng
MYManjuan Yang
Manjuan Yang

26 July 2011
Verified
Conference Paper
Closed access
MYMan-Juan Yang
Man-Juan Yang
KWKe-Man Wu
Ke-Man Wu
LZLian-De Zhong
Lian-De Zhong
Lane Management Techniques (LMT) discussed in this paper is a traffic flow control measure for multilane freeways by means of restricting lane access by vehicle type and limiting speed by lane and by vehicle type. Five methods of lane management are analyzed and compared in this paper. Lane utilization ratio, times of lane-changing, and speed difference between different lanes and different vehicle-types are selected and used as evaluation indices.. Using an eight-lane freeway in southern China as an example, we developed a calculation model considering variables such as road, traffic and management conditions. Based on the simulation software using VISSIM, a suitable lane management measure is selected for this eight-lane freeway. LMT can also be applied to other multilane freeways by taking different design parameters and traffic composition into consideration.