Yasushi Yamamoto

Yasushi Yamamoto

Auto-generated profile, based on publicly available information

Yasushi Yamamoto

Kansai University, Faculty of Engineering Science, Osaka 564-8680, Japan

Research Focus & Metrics

Academic Career Length

35Years (1992-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2013 in Fusion Engineering and Design
Verified
Journal Article
Closed access
KIKenzo Ibano
Kenzo Ibano
RKRyuta Kasada
Ryuta Kasada
YYYasushi Yamamoto
Yasushi Yamamoto
SKSatoshi Konishi
Satoshi Konishi

2 August 2017 in Fusion Science and Technology
Verified
Journal Article
Closed access
YYYasushi Yamamoto
Yasushi Yamamoto
HKHiroki Konda
Hiroki Konda
YMYuki Matsuyama
Yuki Matsuyama
HOHodaka Osawa
Hodaka Osawa
MOMasami Ohnishi
Masami Ohnishi
The first tritium burning experiments of the discharge type fusion neutron source were conducted in January 2015, using a 93% deuterium and 7% tritium gas mixture. In order to conduct the experiment in a closed environment, a gas feed and exhaust system using non-evaporable getter material was prepared. This system was designed to minimize tritium usage and produce measurable changes in the neutron production rate on the basis of the dependence of the equilibrium pressure on getter temperature as included in the manufacturer’s data sheet. However, the present experiments revealed that the gas supply was insufficient and that the discharge duration was limited to about 2 minutes by the pressure drop during discharge. To determine the cause, verification experiments using hydrogen and deuterium gas were performed. It was found that the pressure variation with getter temperature could be mimicked by exploiting isotope effects and adjusting the hydrogen/deuterium concentration in the getter material according to the gas released into the vacuum chamber. Moreover, prolonged maintenance of a discharge was demonstrated by roughly tripling the amount of gas. The tritium concentration in the gas mixture, estimated on the basis of the present results, varied between 1.5% and 6.7% according to the assumptions used.

1 June 1992 in Japanese Journal of Applied Physics
Verified
Journal Article
Closed access
MOMorihiro Okada
Morihiro Okada
HTHisayuki Toku
Hisayuki Toku
YYYasushi Yamamoto
Yasushi Yamamoto
KYKiyoshi Yoshikawa
Kiyoshi Yoshikawa
A Hall accelerator-type ion source for low-voltage continuous operation (hereafter called HALOC) without any exhaustible filaments, designed for film coating purposes, has successfully produced a large-area low-energy continuous beam of methane or oxygen. The thin film of carbon uniformly coated on a steel plate by the HALOC has been found to be a typical amorphous hard carbon film with high Vickers hardness, strong adhesion, and strong anticorrosion properties. The causes of strong adhesion of the film have been studied.

1 June 2009
Verified
Conference Paper
Closed access
TKT. Kanagae
T. Kanagae
KNK. Noborio
K. Noborio
YYY. Yamamoto
Y. Yamamoto
SKS. Konishi
S. Konishi
A discharge-type tube shaped neutron source has been developed utilizing fusion reactions on the surface of the cylindrical electrodes in the device. Neutron beam can be generated with adequate reflector design. From the neutronic analyses using the MCNP; three-dimensional particle transport code, using H2O or D2O as a reflector is essential to obtain narrow-shaped and sufficiently thermalized neutron beam. Experimental results supported the design and suggest the feasibility of table top fusion neutron beam based on this concept.

1 December 2015 in Journal of Gastrointestinal and Liver Diseases
Verified
Journal Article
Open access
RHRintaro Hashimoto
Rintaro Hashimoto
YYYasushi Yamamoto
Yasushi Yamamoto
TTTokuma Tanuma
Tokuma Tanuma