26 June 2019 in IEEE Transactions on Industrial Electronics
A soft-switched nonisolated high step-up dc–dc converter based on the quasi-impedance-source structure is presented in this paper. In the proposed converter, a technique similar to the synchronous rectifier is applied such that the diode of the impedance network is replaced with an active switch. In this way, not only is conduction loss associated with the diode reduced but also zero-voltage-switching characteristics for power switches are provided. Also, output diodes of the proposed converter are switched under zero-voltage-zero-current-switching condition which extremely reduces their switching and reverse-recovery losses. It is shown that by correct design of the components, soft-switching performance is retained for all the semiconductor devices over the entire range of output load. All these factors together with simplicity of the proposed structure result in high efficiency over a wide range of output power. Moreover, the proposed converter benefits from continuous input current and a shared ground between input and output. Operating principles of the proposed converter along with its steady-state analysis are presented. Also, experimental results obtained from a laboratory prototype for 48 V to 350 V voltage conversion and 100 W nominal power are provided to validate the feasibility of the proposed converter.
1 May 2016 in IET Power Electronics
To enhance the gain of conventional boost converters in applications such as fuel cells and photovoltaic systems, cascade boost converters are normally applied. In this study, a new cascade boost converter topology with reduced conduction losses is proposed. This converter shows reduced root‐mean‐square currents of the circuit elements and reduced conduction losses. The proposed converter is analysed and compared with the conventional circuit topology. The proposed converter has all the advantages of cascade boost converter with the advantage of reduced conduction losses. Finally, simulation and experimental results of a 200 W laboratory prototype are presented.
1 August 2015 in IET Power Electronics
Z‐source converter has several advantages such as high‐voltage gain, clamped switch voltage and positive output voltage polarity. This study presents a new non‐isolated high step‐up DC–DC converter which is derived from Z‐source converter and provides higher‐voltage gain compared with its conventional counterpart. Owing to its high‐voltage conversion ratio, the proposed converter is a proper choice for photovoltaic applications. Furthermore, reverse‐recovery problems caused by the output diode are reduced in the proposed converter which reduces the switching losses. In addition, the leakage energy is recycled so the conversion efficiency is improved. Analysis and operating principles of the proposed converter are discussed and design guidelines are presented. Moreover, the effect of non‐ideal elements on the proposed converter performance is analysed. A 100 W laboratory prototype to convert 20–300 V is implemented and experimental results are presented to verify theoretical analysis.
14 January 2019 in IEEE Transactions on Industrial Electronics
Control-to-output transfer function of the classical boost converter in continuous conduction mode contains a right-half-plane (RHP) zero that limits its frequency response. To eliminate this zero and enhance the dynamic performance, a forward path for energy transfer to output within the ON interval of the power switch is provided using the magnetic coupling. This approach simply eliminates the RHP zero by introducing an inductor coupled to the boost inductor, a diode, and a capacitor into the classical boost topology. In addition, the provided forward path enhances the voltage gain which makes it possible to achieve a smaller operating duty cycle and reduced voltage stress for the power switch in applications with large voltage conversion ratios. Using this approach does not complicate the control structure and a traditional single-loop voltage control scheme can be used to regulate the output voltage. The proposed approach is analytically examined by obtaining the averaged state-space model of the resulting converter and a criterion to eliminate the RHP zero is presented. Experimental results from an implemented laboratory prototype for 48 V to 200 V voltage conversion and 100 W nominal power are provided.
28 December 2017 in IEEE Transactions on Power Electronics
A previously proposed high step-up dc-dc converter based on Z-source circuit is improved such that conduction losses of the converter and current stress of its power switch are reduced. The improved converter contains only one magnetic core and all of the inductors are coupled. It is shown that using one core allows us to use windings with lower copper resistance that results in reducing resistive losses of the coupled inductors. Also, by rearranging two diodes of the converter, the switch current and its conduction loss are reduced. In addition, a previously proposed auxiliary circuit for zero-voltage-transition operation is employed with a minor modification that makes it possible to use a relatively large snubber capacitor that significantly decreases current-voltage overlap of the main switch at turn-off instant. Improvement in the overall efficiency of the presented structure over the existing high step-up Z-source converter is demonstrated by implementing a 100-W prototype of each converter for 30- to 300-V voltage conversion.
1 December 2016 in IEEE Transactions on Power Electronics
This paper proposes a new isolated single-stage single-switch soft-switching power-factor-correction (S6-PFC) driver without electrolytic capacitors for supplying light-emitting-diodes (LEDs). In the proposed LED driver, all the semiconductor devices are soft-switched without employing any extra active switch. The leakage inductance of transformer acts as a resonant component so that the leakage energy is recycled. Soft-switching operation of the semiconductor devices together with absorption of the leakage energy improve the proposed driver efficiency. Furthermore, input current of the driver has very low harmonics resulting in high power-factor. Operating principles of the proposed S6-PFC LED driver as well as its design guidelines are presented. Also, experimental results of a laboratory prototype for supplying a 21W/30V LED module from 220V/50Hz AC mains are provided to verify the theoretical analysis. The presented results show that the implemented prototype has an efficiency of 92% under full-load condition and its input current total harmonic distortion (THD) is as low as 2.6%.