Fabian Schwack

Fabian Schwack

Auto-generated profile, based on publicly available information

Fabian Schwack

KTH Royal Institute of Technology

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2020 in Wear
Verified
Journal Article
Open access
FSFabian Schwack
Fabian Schwack
Norbert Fritz BaderNorbert Fritz Bader
Norbert Fritz Bader
JLJohan Leckner
Johan Leckner
CDClaire Demaille
Claire Demaille
GPGerhard W G Poll
Gerhard W G Poll

13 November 2019 in Wind Energy
Verified
Journal Article
Open access
PDF file
MSMatthias Stammler
Matthias Stammler
PTPhilipp Thomas
Philipp Thomas
ARAndreas Reuter
Andreas Reuter
FSFabian Schwack
Fabian Schwack
GPGerhard W G Poll
Gerhard W G Poll
The power control of wind turbines is usually realized via a change in the pitch angle of the rotor blades. Pitching facilitates the exact control of the turbines and the reliable deceleration of the rotor when required. Pitch movements can moreover be used for load control. One of these methods is called individual pitch control (IPC). IPC controls the blades individually and brings about a significant reduction in the fatigue loads and extreme loads placed on the structural components, while at the same time reducing the yield of the turbine only slightly. The lower loads reduce material costs, and thus, the cost of energy (CoE) is reduced, despite the slight reduction in yield. The method is nevertheless not used everywhere since the additional movement cycles put the rotor blade bearings in particular under stress. Special attention must be paid to small amplitude oscillating movements, which carry a high risk of inducing surface damage in the rolling contacts of the blade bearings. This paper uses a cycle analysis of the IWT7.5‐164 reference turbine to illustrate the differences in the movement patterns of wind turbine blade bearings with and without IPC. Moreover, model calculations with single contacts are used to show which of the movement patterns carries a risk of inducing surface damage. The use of IPC leads to the expected load reduction at the blade root. In current literature, IPC is usually assumed to have a negative influence on the life expectancy of blade bearings, but the findings of this study contradict this. The summed blade bearing movement is increased, although the number of very small pitch angles occurring is reduced. This reduction reduces the risk of wear in the blade bearings.

12 November 2021 in Wind Energy
Verified
Journal Article
Open access
PDF file
FSFabian Schwack
Fabian Schwack
FHFabian Halmos
Fabian Halmos
MSMatthias Stammler
Matthias Stammler
GPGerhard Poll
Gerhard Poll
SGSergei Glavatskih
Sergei Glavatskih
We tested two types of ball bearings with an outer diameter of 750 mm to learn more about the challenges of oscillating motions for pitch bearings. The experimental conditions are derived from aero‐elastic simulations, long‐term wind speed measurements and a scaling method that considers loads and pitch angles. As a result, the parameters relevant for pitch bearings are represented appropriately, and the findings are transferable to other bearing sizes. For the tested parameter sets, severe wear occurred for over 90% of the exposed contact areas after 12 500 oscillating cycles. Decreasing the number of cycles to 1250 leads to a mix of exposed areas with 13% severe wear, 32% mild wear and 55% no wear, with no apparent pattern. The results demonstrate that a comparatively small amount of consecutive cycles can lead to severe wear. A new type of bearing tested showed less wear for the selected operating conditions.

30 September 2016 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
FSF Schwack
F Schwack
MSM Stammler
M Stammler
GPGerhard W G Poll
Gerhard W G Poll
ARA Reuter
A Reuter
The fatigue life calculation of bearings under rotating conditions has been well researched and standardized. In contrast, for bearings in oscillating applications no international standards exist. As a result, pitch bearings in wind turbines are designed with different, non standardized approaches. Furthermore, the impact of individual pitch control on pitch bearings has not yet been studied. In this paper four approaches for fatigue life calculation will be applied and compared under individual pitch control conditions. For comparison, the loads and the bearing geometry of the reference turbine IWT 7.5 MW, which is individual pitch controlled, are used. This paper will show how the bearing life calculated by different approaches reacts to individual pitch control conditions. Furthermore, the factors for the modified rating life, according to the ABMA and ISO standards, which implement different operation conditions on the bearings in rotating applications, are calculated for the given loads and the given bearing geometry in oscillating applications.

1 October 2018 in Tribology International
Verified
Journal Article
Closed access
FSF. Schwack
F. Schwack
FPF. Prigge
F. Prigge
GPGerhard W G Poll
Gerhard W G Poll

14 March 2018 in Wind Energy Science
Verified
Journal Article
Open access
PDF file
MSMatthias Stammler
Matthias Stammler
FSFabian Schwack
Fabian Schwack
NBNorbert Bader
Norbert Bader
ARAndreas Reuter
Andreas Reuter
GPGerhard W G Poll
Gerhard W G Poll
Pitch bearings of wind turbines are large, grease-lubricated rolling bearings that connect the rotor blades with the rotor hub. They are used to turn the rotor blades to control the power output and/or structural loads of the turbine. Common actuators turning the blades are hydraulic cylinders or electrical motor–gearbox combinations. In order to design pitch actuator systems that are able to turn the blades reliably without imposing an excessive power demand, it is necessary to predict the friction torque of pitch bearings for different operating conditions. In this paper, the results of torque measurements under load are presented and compared to results obtained using different calculation models. The results of this comparison indicate the various sources of friction that should be taken into account for a reliable calculation model.