Mohamed Eissa Moussa

Mohamed Eissa Moussa

Auto-generated profile, based on publicly available information

Mohamed Eissa Moussa

Casting Technology Department, Manufacturing Technology Institute, Central Metallurgical R&D Institute (CMRDI), Cairo, Egypt

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2018 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MMM.E. Moussa
M.E. Moussa
Mostafa WalyMostafa Waly
Mostafa Waly
MAM. Amin
M. Amin

1 September 2014 in Journal of Magnesium and Alloys
Verified
Journal Article
Open access
MMM.E. Moussa
M.E. Moussa
Mostafa WalyMostafa Waly
Mostafa Waly
AEA.M. El-Sheikh
A.M. El-Sheikh
The effect of Ca addition on modification of primary Mg2Si, hardness and wear behavior in Mg–5 wt.%Si hypereutectic alloy has been investigated. The results showed clearly that without Ca addition, most of primary Mg2Si appeared as coarse dendritic morphology with average size of about 215 μm. With the addition of 0.1 wt.%Ca, the average size of primary Mg2Si decreased to about 98 μm, but their morphologies did not significantly changed. As the addition level of Ca increased to 0.3 wt.%, the average size of primary Mg2Si decreased significantly to about 50 μm and their morphologies changed to polyhedral shape. However, with further increasing Ca addition to 0.6 wt.% and 1 wt.%, some needle-like and blocky CaMgSi particles formed and the average size of primary Mg2Si increased slightly, which could described as over-modification. The present work showed that the optimal modification effect could be obtained when the Ca content in the investigated alloy reached 0.3 wt.%. The modification mechanism may be referred mainly due to poisoning effect resulting from the segregation of Ca atoms at the growth front of the Mg2Si and the adsorption effect of some Ca atoms in the Mg2Si crystal growth plane. The 0.3 wt.%Ca-added alloy has the highest hardness value and the best wear resistance among all other alloys. An excessive Ca addition resulted in the formation of some needle-like and blocky CaMgSi particles, which was detrimental to hardness and wear behavior of the 0.6 wt.% and 1 wt.%Ca-added alloys. The wear mechanism of investigated alloys is a mild abrasive oxidative wear with little adhesion

1 November 2013 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MMM.E. Moussa
M.E. Moussa
Mostafa WalyMostafa Waly
Mostafa Waly
AEA.M. El-Sheikh
A.M. El-Sheikh

1 December 2014 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MMM.E. Moussa
M.E. Moussa
Mostafa WalyMostafa Waly
Mostafa Waly
AEA.M. El-Sheikh
A.M. El-Sheikh

1 July 2019 in Transactions of Nonferrous Metals Society of China
Verified
Journal Article
Closed access
MMM.E. Moussa
M.E. Moussa
SEShimaa El-Hadad
Shimaa El-Hadad
WKW. Khalifa
W. Khalifa

23 February 2022 in International Journal of Metalcasting
Verified
Journal Article
Open access
PDF file
MMM. E. Moussa
M. E. Moussa
MAM. Amin
M. Amin
KIKhaled M. Ibrahim
Khaled M. Ibrahim
Effect of ultrasonic vibration (USV) treatment on microstructure and mechanical properties of brass alloy has been investigated. Microstructure of the investigated brass alloy without USV treatment exhibited stretched and dendritic α-phase within an average length of 165 µm and also interdendritic coarse β-phase. By applying USV treatment, the α-phase is significantly refined that obtained an average length of 21 µm. In addition, USV treatment achieved more homogenized structure of α and β-phases. The refinement of microstructure enhanced of course the mechanical properties of the brass alloy including yield strength, ultimate tensile strength, elongation, hardness and wear resistance. Furthermore, fracture surfaces and worn surfaces mechanisms were also discussed.