14 April 2009 in Journal of Fluid Mechanics
We study the dynamics of a single two-dimensional elliptical particle sedimenting in a Newtonian fluid using numerical simulations. The main emphasis in this work is to study the effect of boundaries on the flow patterns observed during sedimentation. The simulations were performed using a multi-block lattice Boltzmann method as well as a finite-element technique and the results are shown to be consistent. We have conducted a detailed study on the effects of density ratio, aspect ratio and the channel blockage ratio on the flow patterns during sedimentation. As the channel blockage ratio is varied, our results show that there are five distinct modes of sedimentation: oscillating, tumbling along the wall, vertical sedimentation, horizontal sedimentation and an inclined mode where the particle sediments with a non-trivial orientation to the vertical. The inclined mode is shown to form a smooth bridge between the vertical and horizontal modes of sedimentation. For narrow channels, the mode of sedimentation is found to be sensitively dependent on the initial orientation of the particle. We present a phase diagram showing the transitions between the various modes of sedimentation with changing blockage ratio of the channel.
7 June 2012 in Journal of Fluid Mechanics
In the traditional hybrid RANS/LES approaches for the simulation of wall-bounded fluid turbulence, such as detached-eddy simulation (DES), the whole flow domain is divided into an inner layer and an outer layer. Typically the Reynolds-averaged Navier–Stokes (RANS) equations are used for the inner layer, while large-eddy simulation (LES) is used for the outer layer. The transition from the inner-layer solution to the outer-layer solution is often problematic due to the lack of small-scale dynamics in the RANS region. In this paper, we propose to simulate the whole flow domain by large-eddy simulation while enforcing a Reynolds-stress constraint on the subgrid-scale (SGS) stress model in the inner layer. Both the algebraic eddy-viscosity model and the one-equation Spalart–Allmaras (SA) model have been used to constrain the Reynolds stress in the inner layer. In this way, we improve the LES methodology by allowing the mean flow of the inner layer to satisfy the RANS solution while small-scale dynamics is included. We validate the Reynolds-stress-constrained large-eddy simulation (RSC-LES) model by simulating three-dimensional turbulent channel flow and flow past a circular cylinder. Our model is able to predict mean velocity, turbulent stress and skin-friction coefficients more accurately in turbulent channel flow and to estimate the pressure coefficient after separation more precisely in flow past a circular cylinder compared with the pure dynamic Smagorinsky model (DSM) and DES using the same grid resolution. Furthermore, the computational cost of the RSC-LES is almost the same as that of DES.
8 July 2013 in Physical Review E
The momentum exchange method has been widely used in lattice Boltzmann simulations for particle-fluid interactions. Although proved accurate for still walls, it will result in inaccurate particle dynamics without corrections. In this work, we reveal the physical cause of this problem and find that the initial momentum of the net mass transfer through boundaries in the moving-boundary treatment is not counted in the conventional momentum exchange method. A corrected momentum exchange method is then proposed by taking into account the initial momentum of the net mass transfer at each time step. The method is easy to implement with negligible extra computation cost. Direct numerical simulations of a single elliptical particle sedimentation are carried out to evaluate the accuracy for our method as well as other lattice Boltzmann-based methods by comparisons with the results of the finite element method. A shear flow test shows that our method is Galilean invariant.
22 December 2015 in Journal of Fluid Mechanics
A series of direct numerical simulations of turbulent channel flow with spanwise rotation at fixed global friction Reynolds number is performed to investigate the rotation effects on the mean velocity, streamwise velocity fluctuations, Reynolds shear stress and turbulent kinetic energy. The global friction Reynolds number is chosen to be $Re_{{\it\tau}}=u_{{\it\tau}}^{\ast }h^{\ast }/{\it\nu}^{\ast }=180$ ( $u_{{\it\tau}}^{\ast }$ is the global friction velocity, $h^{\ast }$ is the channel half-width and ${\it\nu}^{\ast }$ is the kinematic viscosity), while the global-friction-velocity-based rotation number $Ro_{{\it\tau}}=2{\it\Omega}^{\ast }h^{\ast }/u_{{\it\tau}}^{\ast }$ ( ${\it\Omega}^{\ast }$ is the dimensional angular velocity) varies from 0 to 130. In the previously reported $2{\it\Omega}^{\ast }$ -slope region for the mean velocity, a linear behaviour for the streamwise velocity fluctuations, a unit-slope linear profile for the Reynolds shear stress and a $-2Ro_{{\it\tau}}$ -slope linear profile for the production term of $\langle u^{\prime }u^{\prime }\rangle$ have been identified for the first time. The critical rotation number, which corresponds to the laminar limit, is predicted to be equal to $Re_{{\it\tau}}$ according to the unit-slope linear profile of the Reynolds shear stress. Our results also show that a parabolic profile of the mean velocity can be identified around the ‘second plateau’ region of the Reynolds shear stress for $Ro_{{\it\tau}}\geqslant 22$ . The parabolas at different rotation numbers have the same shape of $1/Re_{{\it\tau}}$ , the radius of curvature at the vertex. Furthermore, the system rotation increases the volume-averaged turbulent kinetic energy at lower rotation rates, and then decreases it when $Ro_{{\it\tau}}\gtrsim 16$ .
1 November 2014 in Journal of Fluids and Structures
26 October 2020 in Physical Review E
In this paper we derive an exact expression for the mean heat flux at the wall for the compressible turbulent channel flow. In the expression, the heat flux at the wall can be decomposed into four parts, including the contribution from the turbulent heat transfer, the contribution from the molecular heat transfer, the contribution from the pressure work, and the contribution from the work from viscous stress (VW). The decomposition is validated in compressible turbulent channel flows with isothermal walls at three different Reynolds and Mach numbers, and the results match very well with the direct estimations at the wall. The data also show that the VW term dominates the contributions (around ) in the decomposition while around of VW is from the near-wall region , illustrating the importance of the viscous stress work in the near-wall region.