Persistent scatterer interferometry (PSI) has matured to an established method for detection of large-scale and small-scale deformation phenomena in urban areas and of man-made infrastructure. Deformation regimes originating from oil, gas, or water extraction, storage of gas underground, CO2 sequestration, loading of dams and dykes, and mining activities are prominent examples for investigations that have been carried out successfully applying the PSI technique to ERS or ENVISAT data stacks. Due to the sparse spatial distribution of persistent scatterers (PSs) and the moderate resolution of the mentioned satellites it has usually not been possible to track down the source of scattering in detail. The use of PSs was also opportunistic, that is, the PSI monitoring of individual buildings or specific parts of infrastructure was not always been guaranteed. This situation changes dramatically if PSI is applied to very high resolution data obtained from modern radar satellites like TerraSAR-X or COSMO-Skymed. For example, TerraSAR-X is able to deliver images with a resolution of up to 1 m in azimuth and 0.6 m in slant range when operated in the so-called high-resolution spotlight mode with 300 MHz bandwidth. This kind of data provide much more details of single objects and at the same time much higher PS densities. Compared to ERS or ENVISAT type data, the PS density can increase by factors of 100–200 on the same area. This is caused by the physical fact that at higher resolution and shorter wavelength, small scatterers (e.g., trihedrals) show higher signal-to-clutter ratio. Often, several tens to more than a hundred PSs can be found on a single large building facade or roof. Thus, individual buildings and infrastructure can be monitored in terms of structural stress and seasonal deformation, which is also supported by the short revisiting time of only 11 days of TerraSAR-X. Besides on resolution, the density of these points also depends on additional acquisition parameters like incidence angle or polarization and also on the three-dimensional (3D) structure of the given scene, as regions of layover areas and shadow are closely related to the geometrical configuration. The dependence of PS density on these parameters is discussed in this article utilizing results of PSI analysis of different high-resolution TerraSAR-X spotlight data stacks. In addition to this increase of resolution, TerraSAR-X products benefit from a high absolute slant range georeferencing accuracy of 0.5–1 m, which supports a very precise absolute 3D localization of the PSs on the same order. Hence, the physical nature of a PS can be investigated in more detail helping the understanding of the scattering source of the man-made infrastructure. Results of 3D localization and deformation assessment on several test sites are presented in this article.
6 December 2013 in IEEE Transactions on Geoscience and Remote Sensing
This paper presents a new technique for mapping mean deformation velocity in highly decorrelated areas with known deformation patterns, exploiting high-resolution synthetic aperture radar (SAR) data. The implemented method is based on distributed scatterers and first makes use of the Anderson-Darling (AD) statistical test to identify homogenous patches of pixels based on SAR amplitude images. Then, a robust object adaptive parameter estimation is performed to estimate the local gradients of deformation velocity and the local gradients of residual DEM in range and azimuth directions for these patches, utilizing small baseline differential interferograms. Finally, the information obtained from different patches is connected to get the deformation velocity, via a 2-D model-based deformation integration using Bayesian inference. Compared with published multitemporal interferometric work, the main advantage of the newly developed algorithm is that it does not require any phase unwrapping, and because of this, the method is largely insensitive to decorrelation phenomenon occurring in natural terrains and the availability of persistent scatterers (PSs), in contrast to the coherent stacking techniques such as PS interferometry, small baseline subset algorithm, and SqueeSAR. The method is computationally inexpensive with respect to SqueeSAR as only the small baseline interferograms are used for the processing. The method provides spatially dense deformation velocity maps at a suitable object resolution, as compared with a few measured points provided by the stacking techniques in difficult decorrelated regions. High Resolution Spotlight TerraSAR-X data set of Lueneburg in Germany is used as a processing example of this technique.
17 January 2005 in IEEE Transactions on Geoscience and Remote Sensing
This paper presents theory, algorithm, and results of a maximum-likelihood algorithm that is capable to fuse a number of heterogeneous synthetic aperture radar interferograms into a single digital elevation model (DEM) without the need for the critical phase-unwrapping step. The fusion process takes place in the object space, i.e., the map geometry, and considers the periodic likelihood function of each individual interferometric phase sample. The interferograms may vary regarding their radar wavelength, their baseline, their heading angle (ascending or descending), and their incidence angle. Geometric baseline error estimates and a priori knowledge from other estimates like existing DEMs are incorporated seamlessly into the estimation process. The presented approach significantly differs from the standard DEM generation method where each interferogram is first phase-unwrapped individually, then geocoded into a common map geometry, and finally averaged with DEMs generated from other interferograms. By avoiding the phase-unwrapping step, the proposed algorithm does not depend on gradients between samples and is therefore capable to reconstruct the arbitrary height of each single scatterer. Because the height of each DEM sample is determined individually, spatial propagation of phase-unwrapping errors is avoided. The algorithm is targeted to fuse an ensemble of interferometric multiangle or multibaseline observations in areas of rugged terrain or highly ambiguous data where algorithms based on phase unwrapping may fail. The algorithm is explained, and examples with real data from the Shuttle Radar Topography Mission are given. Conditions of future missions are simulated, and optimization criteria for the viewing geometry are discussed.
1 November 2009 in Photogrammetrie - Fernerkundung - Geoinformation