3 October 2016 in Nature Communications
Owing to the limited spatio-temporal resolution of display devices, dynamic holographic three-dimensional displays suffer from a critical trade-off between the display size and the visual angle. Here we show a projection-type holographic three-dimensional display, in which a digitally designed holographic optical element and a digital holographic projection technique are combined to increase both factors at the same time. In the experiment, the enlarged holographic image, which is twice as large as the original display device, projected on the screen of the digitally designed holographic optical element was concentrated at the target observation area so as to increase the visual angle, which is six times as large as that for a general holographic display. Because the display size and the visual angle can be designed independently, the proposed system will accelerate the adoption of holographic three-dimensional displays in industrial applications, such as digital signage, in-car head-up displays, smart-glasses and head-mounted displays.
23 May 2008 in Journal of Display Technology
A high dynamic range liquid crystal display (HDR-LCD) can enhance the contrast ratio of images by utilizing locally controlled dynamic backlight. We studied the HDR-LCD as a dual-panel display: a backlight module and a liquid crystal (LC) cell. As the gamma of the LC signal, the backlight module was also endowed with a gamma function to control the contrast ratio of HDR images. The inverse of a mapping function (IMF) method proposed as a dynamic gamma mapping curve for the backlight module, has been demonstrated to further improve in HDR image quality. By implementing the IMF method on a HDR-LCD TV with 88 backlight zones, the image contrast ratio can reach while maintaining high brightness, clear image detail, and an average power reduction of 30%.
15 January 2015 in Optics Express
A liquid crystal lens array with a hexagonal arrangement is investigated experimentally. The uniqueness of this study exists in the fact that using convex-ring electrode provides a smooth and controllable applied potential profile across the aperture to manage the phase profile. We observed considerable differences between flat electrode and convex-ring electrode; in particular the lens focal length is variable in a wider range from 2.5cm to infinity. This study presents several noteworthy characteristics such as low driving voltage; 30 μm cell gap and the lens is electrically switchable between 2D/3D modes. We demonstrate a hexagonal LC-lens array for capturing 3D images by using single sensor using integral imaging.
7 June 2010 in Optics Express
This work presents a novel “pulsed spray (PS)” process for the coating of yellow YAG:Ce3+ phosphor on blue InGaN-based light emitting diodes (LEDs). To coat a phosphor layer of high quality on an LED chip surface, the PS approach is used and studied because of the uniform color distribution, providing a wide range of color temperatures. This PS coating approach applies phosphor by exploiting mechanical principles without risk of chemical pollution. Additionally, it can be applied to wire-bonded LEDs and an array of LED chips on a substrate to fabricate a large-area, planar illumination system of high optical quality, which is easy to manufacture.
2 October 2012 in Journal of Display Technology
The fast response superzone Fresnel liquid crystal (LC) lens with multiple transparent electrodes was proposed for temporal scanning auto-stereoscopic display. The experimental results indicated that the superzone Fresnel LC lens not only performed fast switching time (~ 0.2 s), but also had the benefit of low driving voltage (~ 5 Vrms). A 4-inch 2D/3D switchable auto-stereoscopic display with superzone Fresnel LC lens was further demonstrated. Finally, by driving the multiple electrodes alternatively, the superzone Fresnel LC lens array could be moved on horizontal direction for increasing the resolution of auto-stereoscopic display.
7 January 2015 in Optics Letters
Phase-encoded nanostructures such as quick response (QR) codes made of metallic nanoparticles are suggested to be used in security and authentication applications. We present a polarimetric optical method able to authenticate random phase-encoded QR codes. The system is illuminated using polarized light, and the QR code is encoded using a phase-only random mask. Using classification algorithms, it is possible to validate the QR code from the examination of the polarimetric signature of the speckle pattern. We used Kolmogorov–Smirnov statistical test and Support Vector Machine algorithms to authenticate the phase-encoded QR codes using polarimetric signatures.