Michael Kurrat

Michael Kurrat

Auto-generated profile, based on publicly available information

Michael Kurrat

Technische Universität Braunschweig

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2024 in Energy & Environmental Science
Verified
Journal Article
Open access
PDF file
FSFelix Schomburg
Felix Schomburg
BHBastian Heidrich
Bastian Heidrich
SWSarah Wennemar
Sarah Wennemar
RDRobin Drees
Robin Drees
TRThomas Roth
Thomas Roth
FRFridolin Roeder
Fridolin Roeder
This review examines the key process of lithium-ion battery cell formation. Influencing factors, challenges, experimental and simulation tools required for knowledge-based process design of current and emerging battery technologies are addressed.

24 September 2021 in Batteries
Verified
Journal Article
Open access
PDF file
LHLouisa Hoffmann
Louisa Hoffmann
MKManuel Kasper
Manuel Kasper
MKMaik Kahn
Maik Kahn
GGGeorg Gramse
Georg Gramse
Gabriela Ventura SilvaGabriela Ventura Silva
Gabriela Ventura Silva
FKFerry Kienberger
Ferry Kienberger
Lithium-ion batteries are a key technology for electromobility; thus, quality control in cell production is a central aspect for the success of electric vehicles. The detection of defects and poor insulation behavior of the separator is essential for high-quality batteries. Optical quality control methods in cell production are unable to detect small but still relevant defects in the separator layer, e.g., pinholes or particle contaminations. This gap can be closed by executing high-potential testing to analyze the insulation performance of the electrically insulating separator layer in a pouch cell. Here, we present an experimental study to identify different separator defects on dry cell stacks on the basis of electric voltage stress and mechanical pressure. In addition, finite element modeling (FEM) is used to generate physical insights into the partial discharge by examining the defect structures and the corresponding electric fields, including topographical electrode roughness, impurity particles, and voids in the separator. The test results show that hard discharges are associated with significant separator defects. Based on the study, a voltage of 350 to 450 V and a pressure of 0.3 to 0.6 N/mm2 are identified as optimum ranges for the test methodology, resulting in failure detection rates of up to 85%.

5 April 2019 in Energy Technology
Verified
Journal Article
Closed access
PDF file
HHHeiner Hans Heimes
Heiner Hans Heimes
Christian OffermannsChristian Offermanns
Christian Offermanns
AMAhmad Mohsseni
Ahmad Mohsseni
HLHendrik Laufen
Hendrik Laufen
UWUwe Westerhoff
Uwe Westerhoff
AKAchim Kampker
Achim Kampker

1 September 2007
Verified
Conference Paper
Closed access
AMAlexandra Mutzke
Alexandra Mutzke
TRThomas Ruther
Thomas Ruther
MKMichael Kurrat
Michael Kurrat
MLManfred Lindmayer
Manfred Lindmayer
EWErnst-Dieter Wilkening
Ernst-Dieter Wilkening
Investigations on the arc splitting process in low- voltage arc chutes have shown that a threshold voltage has to be exceeded before new arc roots form. When an arc spot has been formed, the electrode fall is nearly constant and rather independent of the current. In simulations a thin layer of elements with a nonlinear current density-voltage characteristic surrounding the splitter plate represents the formation of new arc roots. To model this behavior a characteristic with a voltage hump at low current densities and a constant final voltage at higher current densities has been presented in former publications. In this paper, the influence of the magnitude of the voltage hump is studied. A lower voltage hump yields a smaller arc loop around the front edge of the splitter plate and an earlier subdivision of the arc. A too high voltage hump makes arc splitting impossible. A comparing simulation without any arc root model, but only with the properties of the metallic plates, shows that a realistic simulation of the arc splitting process needs special treatment of the arc roots. The results are compared and verified on the basis of experimental results. Hence, the arc splitting process is analyzed concerning arc voltage and current through the plate as well as location of the arc roots.

13 May 2021 in Batteries
Verified
Journal Article
Open access
PDF file
Daniel KehlDaniel Kehl
Daniel Kehl
TJTorben Jennert
Torben Jennert
FLFrank Lienesch
Frank Lienesch
MKMichael Kurrat
Michael Kurrat
The reuse and repurposing of lithium-ion batteries for transportation in stationary energy systems improve the economic value of batteries. A precise suitability test at the beginning of the second life is therefore necessary. Common methods such as electrochemical impedance spectroscopy (EIS) and current interrupt (CI) analysis, as well as capacity analysis, can be used for testing. In this paper, these methods are studied from the aspects of test duration, sensitivity and acquisition costs of the measuring instruments. For this purpose, tests are carried out on battery modules, which were used for transportation. It is shown that subtle differences are better detected with EIS and less accurately with the CI method. The test duration is fastest with the CI method, followed by EIS and the capacity test. Strongly aged modules are reliably detected with all methods.

26 January 2021 in Batteries
Verified
Journal Article
Open access
PDF file
KRKerstin Ryll
Kerstin Ryll
LHLouisa Hoffmann
Louisa Hoffmann
OLOliver Landrath
Oliver Landrath
FLFrank Lienesch
Frank Lienesch
MKMichael Kurrat
Michael Kurrat
The cell characterization in the incoming inspection is an important but time and cost intensive process step. In order to obtain reliable parameters to evaluate and classify the cells, it is essential to design the test procedures in such a way that the parameters derived from the data allow the required statements about the cells. Before the focus is placed on the evaluation of cell properties, it is therefore necessary to design the test procedures appropriately. In the scope of the investigations two differently designed incoming inspection routines were carried out on 230 commercial lithium-ion battery cells (LIBs) with the aim of deriving recommendations for optimal test procedures. The derived parameters of the test strategies were compared and statistically evaluated. Subsequently, key figures for the classification were identified. As a conclusion, the capacity was confirmed as an already known important parameter and the average cell voltage was identified as a possibility to replace the usually used internal resistance. With regard to capacity, the integration of CV steps in the discharging processes enables the determination independently from the C-rate. For the average voltage cycles with high C-rates are particularly meaningful because of the significant higher scattering due to the overvoltage parts.