Marina Zaitseva

Marina Zaitseva

Auto-generated profile, based on publicly available information

Marina Zaitseva

Don State Technical University

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 September 2018 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
TRTatyana M. Rogovenko
Tatyana M. Rogovenko
MZMarina M. Zaitseva
Marina M. Zaitseva
This paper presents an evaluation of the minimum dipper stick service life in the unsafe cross-section; it is based on statistical simulation known as Monte Carlo method. Source data on the bearing capacity parameters as well as on the values of stresses in the unsafe cross-section are presented as small samples. Statistical simulation is used to create a finite general population of data on machine parts my means of an intermediate subpopulation using order statistics distributions.

7 November 2017 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
TRTatyana Rogovenko
Tatyana Rogovenko
MZMarina Zaitseva
Marina Zaitseva
This paper applies the statistical modeling method to provide a quantitative assessment of risks emerging at sudden failures of construction equipment. The risk mathematical model takes into consideration the distribution parameters of operation, downtime and repair hours determined for a general population of the failed part finite volume. The proposed modeling algorithm is applied to assess risks at sudden dipper stick failures. The modeling results allow one to evaluate the tolerable period for the equipment use under the set risk levels.

23 May 2017 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
TRTatyana Rogovenko
Tatyana Rogovenko
MZMarina Zaitseva
Marina Zaitseva
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry

1 December 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
VDV Deryushev
V Deryushev
MZM Zaitseva
M Zaitseva
GMG Megera
G Megera
AFA Fedyanov
A Fedyanov
Identification of dynamic characteristics of the machine suspension materials is required for troubleshooting and improving the ride quality. The method of identifying the suspension materials characteristics, based on the application of needle-shaped variation of the L.S. Pontryagin dynamical system to the invariant features of the dynamic system actual movement is presented in this study. The use of the needle-shaped parameters variation to the Hamilton-Ostrogradskyi action integral gives a condition of the objective functional minimum in the form of the maximum principle with the exception of the consideration of the vector of conjugate variables. As a result, the computational costs are reduced, the task of identification and optimization is simplified the convergence and accuracy of the algorithms is improved [1 - 5].

1 December 2019 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
VDVictor V. Deryushev
Victor V. Deryushev
MZMarina M. Zaitseva
Marina M. Zaitseva
DEDmitriy Z. Evseev
Dmitriy Z. Evseev
EKEugene E. Kosenko
Eugene E. Kosenko
Considerable thermal stresses arising in thin-walled metallic materials and structures loaded with tensile stresses can lead either to their complete destruction or to the appearance of discontinuity zones in them.

6 June 2023 in Safety of Technogenic and Natural Systems
Verified
Journal Article
Open access
PDF file
VDV. V. Deryushev
V. V. Deryushev
STSvetlana Teplyakova
Svetlana Teplyakova
MZM. M. Zaitseva
M. M. Zaitseva
Introduction. At the stage of designing technical devices and performing appropriate strength calculations of metal structures, sufficiently large reserves of strength are taken, which, theoretically, exclude any failures of parts. In fact, the machines work with frequent failures. Of interest are undiagnosed failures that lead to a critical decrease in safety, especially at hazardous production facilities. It is assumed that the previously applied approaches of selective determination of the maximum (minimum) reliability value, based on point estimates of the distribution parameters of the two-parameter Weibull law, lead to an overestimation of the calculated indicators of the probability of failure-free operation, i.e. underestimation of risk. Therefore, the work objective is to consider an approach to assessing the risk of operating production facilities in a situation of accidental occurrence of dangerous and undiagnosed failures in systems.Materials and Methods. Methods for technical devices safety assessment based on probability theory were used in the work, and the probability of machine failure was determined based on the well-known method of reliability theory. This method consists in calculating and constructing distribution functions of random variables (load-bearing capacity and loading) that influence the occurrence of failure. The level of increase in the reliability index was determined, leading to frequent unpredictable failures of technical devices (machines) and a decrease in the safety of their operation.Results. The signs of inconsistency of strength calculations based on overestimated safety margins, which in theory exclude failures of parts and machines in general, are identified and substantiated. A new approach to risk assessment of operating production facilities in a situation of accidental occurrence of dangerous and undiagnosed failures by safety systems has been developed and implemented. An algorithm for determining the three parameters of Weibull's law for a population based on sample data has been developed. The resource distribution densities of the boom of the single-bucket excavator EK-14 are constructed. The recommendations are given to increase the probability of failure-free operation to 0.9989.Discussion and Conclusion. The results of the conducted research allow us to substantiate a new approach to risk assessment of operating production facilities in the event of dangerous and undiagnosed failures of basic parts by safety systems, leading to negative consequences.