13 November 2019 in Eastern-European Journal of Enterprise Technologies
Most of the designs of vacuum-evaporators for concentration have the problem of heat supply stabilization over the entire heat exchange surface. This is due to the presence of a steam shell, which complicates the uniform heat supply. The shortcomings also include the lack of the possibility of the rational increase in the heat transfer surface, which in turn affects the duration of thermal treatment and product quality. In order to eliminate the main disadvantages of vacuum-evaporators, it is proposed to use the method of heat supply with increased heating surface. To solve the set improvement tasks, it is proposed to use modern flexible film resistive electric heaters of radiation type (FFREhRT). They are characterized by low inertia, metal capacity, ease of automation and maintenance. Such electric heater is capable to ensure the uniformity of heat flow and to take any geometric shape of the heat transfer surface. In accordance with the design and technological solution, it is proposed to perform heating with the heat-insulated FFREhRT, which is also located in the hollow space of the stirrer and blades shaft and blades, instead of steam shell. Thus, the increase in heat transfer surface from 3.7 m3 to 4.15 m3, that is by 12 %, is ensured.We detected a decrease in boundary shear stress at an increase in temperature: if t=10 °C, q0=79 Pа; respectively, t=70 °C, q0=12 Pа. Effective viscosity at t=10 °C is ηef =392 Pа∙s, for t=70 °C ηef =2 Pа∙s. In the course of testing the model sample of the VEHS during concentration (50...65 °C), shear rate was determined: 0.5...2.5 s-1. Effective viscosity is within 2.0...4.5 Pа∙s. The improved VEHS is characterized by the reduced duration of entering the stationary mode decreased by 29 % compared to the prototype (MZS-320). The effectiveness of the design and technical solution is proved by a decrease in the weight of the unit by 35 %, of specific metal capacity by 42 %, of treatment duration by 12 %
30 August 2024 in Eastern-European Journal of Enterprise Technologies
The object of the study is the oxidative stability of the lipid component of linseed treated with a citric acid and sodium chloride solution. The rational composition of chemical reagents for inactivating linseed lipoxygenases was determined in the work. The obtained results make it possible to develop an effective linseed treatment method for increasing stability to oxidative spoilage. The proposed composition of the linseed treatment solution (citric acid – 1.0...1.3 %; sodium chloride – 0.6...0.8 %) significantly reduces the peroxide and anisidine numbers of the lipid component. This helps reduce oxidative spoilage during accelerated oxidation and storage under normal conditions. Rational treatment conditions were determined based on the approximate dependency of these indicators on the concentrations of chemical reagents. The data obtained in the work are explained by chemical interactions between the solution components and the enzyme complex of linseed, leading to enzyme denaturation and, accordingly, increased oxidative stability of the lipid component. A feature of the obtained results is the competitiveness of treated linseed, characterized by increased nutritional value due to improved technological properties. The results of the study allow minimizing the loss of nutritional value and increasing the shelf life of linseed products. The results are important for developing new oilseed processing technologies. This makes it possible not only to increase the stability of products against oxidative spoilage, but also to preserve their high nutritional value. Further research in this area will contribute to improving oilseed processing technologies, in particular linseed, which is an important contribution to the development of the food industry
31 October 2021 in Eastern-European Journal of Enterprise Technologies
A formulation composition and a low-temperature technique have been devised for concentrating fruit and vegetable puree with the following component content: 20 % apple; 20 % pumpkin; 15 % beets; 15 % cranberries; 15 % hawthorn. The puree is concentrated in a rotary evaporator to a solids content of 50 % at a temperature of 50...56 °C under vacuum. The processing time was reduced to 1...2 min, which is several times less compared to conventional single-case pump vacuum evaporators (60...90 mins). Reducing the temperature influence of concentrating contributes to an increase in the organoleptic and physicochemical parameters of the resulting paste. To determine the effect of the contribution of each component to the structure of the paste, the structural and mechanical properties of the puree from each raw material and concentrated semi-finished products were investigated. The devised paste has an increased strength of the structure with a dynamic viscosity value of 394 Pa⋅s, which is 2.5 times more than that in the control sample. The devised blended fruit and vegetable paste has an increased content of physiologically functional ingredients and good organoleptic parameters, unlike control (apple paste). It was established that the partial replacement of apple puree in the formulation composition of marshmallow with 75 % of the devised multicomponent fruit and vegetable paste gives the product original properties. The dynamic viscosity value of the marshmallow in which 75 % of apple puree was replaced with the devised paste has increased, compared to the control sample (marshmallow without additives), from 408 Pa⋅s to 908 Pa⋅s. The color of the marshmallow mass where 75 % of apple puree were replaced is bright pink with a wavelength of 596.7 nm and a brightness of 62.3 %. The data reported here make it possible to improve the quality of original marshmallow products when adding fruit and vegetable semi-finished products whereby an increase in functional properties is provided
28 December 2021 in Eastern-European Journal of Enterprise Technologies
This paper reports the development of a technology for a fat-based semi-finished product, which was used in the manufacturing of products made from butter sponge-cake batter. When combining high-oleic type oils, beeswax, and monoglyceride, the dense emulsion "oleogel" is formed, which can replace fatty products in flour products technology. The fat-based semi-finished product devised fully matches the technological functions of margarine. The expediency of using sunflower oil of high-oleic type (90.0 %) was established, as a base for the fat-based semi-finished product, as well as the rational percentage of organogelators (monoglyceride, 7 %, beeswax, 3 %), which would ensure the production of a fat-based semi-finished product for the target purpose. The feasibility of using a fat-based semi-finished product has been determined in order to solve two tasks: the introduction of a fat-based semi-finished product that contains high-oleic sunflower oil and has several functional benefits of a healthy diet. The fat-based semi-finished product devised could replace butter in the butter sponge cake technology. It was established that the use of the fat-based semi-finished product ensures the production of products from sweet dough, characterized by the highest values of specific volume and porosity. Applying the fat-based semi-finished product makes it possible to increase the yield of finished products (shrinkage decreases by 19.5 % compared to the control sample, to 18.4 %). The parameters for storing finished products from sweet dough containing the fat-based semi-finished product have been substantiated. It was determined that intensive fat release begins on day 7 of storage of finished products. After 10 days of storage, the experimental samples of sponge cakes release 2.0 times less fat than the control sample. The technology for making products from sweet dough using the fat-based semi-finished product has been developed.
10 December 2018 in Eastern-European Journal of Enterprise Technologies
Studying the influence of hydrothermal treatment parameters on the properties of wheat flour in the technology of a croquette mass
11 November 2020 in ScienceRise
The object of the research is the process of radiation heat transfer, taking into account a single reflection of rays in the IR device of food production. Investigated problem – the work is devoted to solving the problem of irregularity of radiation heat transfer during infrared roasting of food products. Main scientific results. The inverse problem of heat transfer by radiation has been solved and a technique has been developed for determining the profiles of the ray flux reflectors for uniform irradiation of receivers of a convex section. Analytical modeling of all-round uniform irradiation of an elliptical receiver has been carried out. An experimental device with low-inertia temperature sensors for infrared roasting of semi-finished meat products has been developed, which makes it possible to use a reflector shaped according to the developed analytical technique. The verification of the created technique for determining the profiles of reflectors by means of a computer experiment using the TracePro and Mathcad software systems has been carried out. The area of practical use of the research results: the use of an experimental device with a radiant flux reflector for roasting semi-finished meat products proves that the obtained technique for profiling reflectors of heat engineering systems is acceptable for the design of infrared equipment for food production and restaurant facilities. This technique allows simulating the profile of the radiant flux reflector depending on the shape of the receiver. Studies have shown that the use of a profiled reflector in the experimental device reduces the duration of roasting of natural portioned semi-finished beef products by 33 %. Innovative technological product: a technique for determining the profiles of ray flux reflectors for uniform irradiation of receivers with a convex section. Device for infrared roasting of semi-finished meat products. Scope of application of an innovative technological product. The study of an experimental device with a designed radiant flux reflector for roasting semi-finished meat products proves that the obtained technique for profiling reflectors of heat engineering systems is acceptable for the design of infrared equipment for food production and restaurant facilities. Using this approach allows to approach the solution of the problem of irregularity of irradiation of products during infrared roasting