In urban areas, emergency vehicles (EVs) need efficient traffic signal preemption to ensure timely responses during peak hours. While emergency vehicle traffic signal preemption (EVTSP) has garnered significant attention in the literature, the issues of queue spillbacks and negative impacts on non‐priority traffic have been relatively underreported. These issues are particularly critical during peak hours, notably in densely populated urban areas. This study presents an EVTSP system that considers queue spillbacks on approaches along the routes of EVs and the negative impacts of signal preemption on non‐priority traffic. The proposed control system has four key components: (1) a queue length management algorithm to ensure that an EV will not be impeded by excessive queues, particularly on its initial approaches along its route; (2) a signal preemption algorithm to guarantee uninterrupted passage of an EV even for approaches experiencing queue spillbacks; (3) a traffic status recovery algorithm to alleviate the extra waiting time for non‐priority vehicles after an EV crosses each intersection; and (4) a signal plan recovery algorithm to smoothly transit traffic signals to normal operation. The experimental results confirm that the proposed system considerably improves the travel time of an EV and mitigates the negative impacts on non‐priority traffic.
1 February 2021 in Journal of Transportation Engineering, Part A: Systems
On-ramp merging areas are congestion-prone segments of freeways. Depending on the aggressiveness of the driving population and the congestion level, the speed variance among travel lanes due to lane changes and ramp-merging flows may be so significant as to affect the optimal settings of deployed traffic control systems, such as metering rates or advisory speed limits. Extending from METANET, this study presents a lane group–based (LGB) traffic model to reflect the temporal and spatial distributions of traffic conditions among lane groups. The proposed model would allow traffic engineers to reliably assess the impacts of lane-changing activities in both upstream and downstream segments of an on-ramp area and better design their coordinated control strategies. To assess the effectiveness of the proposed model, this study has compared its performance with METANET under various traffic scenarios. The comparison results show that the proposed model can yield up to 26.9% improvement on the accuracy of predicting the temporal and spatial evolution of a freeway’s speed at the interchange area where freeway segments often experience extensive lane-changing activities due to on-ramp merging flows.
1 April 2023 in Journal of Transportation Engineering, Part A: Systems
Contending with various recurrent congestion patterns on major freeway corridors has long been a prioritized task of the transportation community. Most of these patterns take place on a freeway interchange’s on-ramp and off-ramp segments where both exiting and merging flows often trigger a series of lane changes, resulting in significant freeway speed reduction and propagation of traffic queues to neighboring surface streets. To concurrently mitigate freeway traffic congestion and minimize any negative impacts on the nearby local arterials, this study has developed an Integrated Real-time Interchange Control (IRIC) system, which maximizes the benefits of both freeway and arterial users by fusing an integrated off-ramp signal control (IOSC) module, an off-ramp queue impact (OQI) model, a lane group-based (LGB) traffic model, and a ramp metering control strategy as well as arterial signal optimization modules. The proposed system with both ramp metering functions and local arterial signal design capabilities can determine whether to implement system-wide optimization or merely the ramp metering based on real-time detected traffic conditions. The evaluation results from experiments have confirmed the effectiveness of the developed real-time interchange control system, especially with respect to its ability of preventing ramp queue overflows to the neighboring arterials and minimizing the off-ramp spillback onto the freeway mainline.
21 November 2025 in IEEE Transactions on Intelligent Transportation Systems
Hard shoulder running is a freeway traffic control strategy that temporarily converts shoulders into travel lanes to increase the roadway capacity during peak hours. Such hard shoulder running sections may terminate at deceleration lanes. In cases where the deceleration lane is a single lane, two exiting traffic streams, one from the rightmost general-purpose lane and the other from the shoulder, must merge onto a single lane. If not properly controlled, such merging activities could potentially result in excessive congestion, especially when exiting volumes are high. Hence, this study proposes an Integrated Proactive Hard Shoulder Running control system to mitigate such potential congestion with hard shoulder running, advisory messages for executing lane changes, and ramp controls to meter the upstream entry flows. The merging impacts of exiting flows on the mainline traffic assessed in the proposed system are estimated with a customized macroscopic traffic model to best preserve the benefits of hard shoulder running while addressing the associated negative impacts. The system’s evaluation first starts with using extensive field data on different days from a Taiwan freeway section to confirm the model’s effectiveness with respect to reduction in congestion and emissions, then followed by extensive performance analyses under various driver compliance rates to the posted lane-changing advisory message. Additionally, multiple commonly used surrogate safety measures are employed to evaluate the proposed system. All analysis results demonstrate that the proposed system for hard shoulder running can indeed yield the expected benefits of reducing delays and emissions, while increasing safety and throughput.
8 June 2022 in Transportation Research Record: Journal of the Transportation Research Board
Diverging diamond interchange (DDI) has received increased attention from the traffic community for its efficiency in reducing delays for vehicles at on- and off-ramps. The conflicting through movements between a DDI’s two crossover intersections mean that its signal plan must concurrently consider the progression for all critical paths to ensure overall efficiency. In light of DDI’s unique geometric features, the design of its signal plans typically starts with the cycle length and green splits for its two crossover intersections, and then employs available progression models to produce the optimal offsets for those critical paths. Such a two-stage design methodology, however, often cannot yield system-wide optimal results because the optimal progression bandwidth and signal settings are interdependent. Moreover, inefficient coordination between its two crossover intersections may cause excessive queues on the DDI’s bridge segment. This paper therefore presents a mixed-integer linear programming (MILP) model that can concurrently optimize the cycle length, green splits, and offsets for a DDI’s two crossover intersections under the given traffic patterns and geometric constraints such as the link length. The results of extensive numerical analyses with a real-world DDI have confirmed the effectiveness of the proposed model and its robustness in response to demand fluctuation.