23 September 2016 in Geophysical Research Letters
9 September 2019 in Journal of Geophysical Research: Solid Earth
We conducted experiments to investigate the influence of pore fluid pressure on the frictional strength and slip behavior of gouge bearing faults. Saw cut porous sandstone samples with a layer of gouge powders placed between the precut surfaces were deformed in the conventional triaxial loading configuration. A series of velocity‐step tests were performed to measure the response of the friction coefficient to variations in sliding velocity. Pore volume changes were monitored during shearing of the gouge. Our results demonstrate that under constant effective pressure, increasing pore pressure stabilizes the frictional slip of faults with all four gouge materials including antigorite, olivine, quartz, and chrysotile. The stabilizing effect is the strongest in antigorite gouge, which shows an evolution of friction parameters from velocity‐weakening toward velocity‐strengthening behavior with increasing pore pressure. Experiments with controlled pore volume show that the pore volume reduction diminishes under high pore fluid pressures, implying an increasing dilation component at these conditions. The dilatant hardening mechanism can explain the observed strengthening. These results provide a possible explanation to the observed spatial correlation between slow slip events and high pore pressure in many subduction zones.
18 August 2018 in Geochemistry, Geophysics, Geosystems
Hydration of a nominally dry rock can cause expansion of the solid volume, resulting in reaction‐induced fracturing and an associated increase in the porosity and permeability of the rock. We study the effect of confinement on the coupling between stress generation, reaction‐induced fracturing, and porosity evolution during the hydration of periclase (MgO) into brucite (Mg(OH)2). Samples of a microporous MgO ceramic were hydrated at 170–210 °C, 5–80 MPa confining pressure, 6–95 MPa differential stress, and 5–75 MPa pore fluid pressure in a purpose‐designed triaxial load cell. Hydration‐induced changes were recorded in situ by X‐ray microtomographic imaging at 5‐min intervals. Below 30 MPa effective mean stress, the fraction of periclase replaced by brucite is a sigmoidal function of time. After a slow start, the replacement rate picks up with concomitant intense fracturing. The porosity increase resulting from the reaction‐induced fractures is transient (pulse‐like). Following the porosity pulse the rate of replacement declines until the replacement is almost complete. Above 30 MPa, the reaction rate is slow, porosity decreases monotonically without any observable fracturing during the time of the experiment. At these stress conditions, the lack of fracturing cannot be limited by the thermodynamic affinity of the reaction. A possible interpretation is that the stress generated by the reaction may overcome the disjoining pressure at the grain‐grain interface, expelling the water film trapped there and thereby dramatically reducing the reaction rate.
31 July 2020 in Journal of Geophysical Research: Solid Earth
TPthe Oman Drilling Project Phase 2 Science Party
the Oman Drilling Project Phase 2 Science Party
+7
Permeability profiles in the crust‐mantle sequences of the Samail ophiolite were constructed based on onboard measurements of the electrical resistivity of cores recovered during the Oman Drilling Project. For each sample, we measured dry and brine‐saturated resistivity during the description campaign on the drilling vessel Chikyu. Owing to the conductive brine in the pore space, wet resistivity is systematically lower than dry resistivity. The difference between dry and wet resistivity is attributed to the movement of dissolved ions in brine that occupies the pore space. We applied effective medium theory to calculate the volume fraction of pores that contribute to electrical transport. Using an empirical cubic law between transport porosity and permeability, we constructed permeability profiles for the crust‐mantle transition zone and the serpentinized mantle sections in the Samail ophiolite. The results indicate that (1) the gabbro sequence has a markedly lower permeability than the underlying mantle sequence; (2) serpentinized dunites have higher permeability than serpentinized harzburgites; and (3) discrete sample permeability is correlated with ultrasonic velocity, suggesting that the permeability variations predominately reflect crack density and geometry.
13 July 2018 in Solid Earth
The olivine carbonation reaction, in which carbon dioxide is chemically incorporated to form carbonate, is central to the emerging carbon sequestration method using ultramafic rocks. The rate of this retrograde metamorphic reaction is controlled, in part, by the available reactive surface area: as the solid volume increases during carbonation, the feasibility of this method ultimately depends on the maintenance of porosity and the creation of new reactive surfaces. We conducted in situ dynamic X-ray microtomography and nanotomography experiments to image and quantify the porosity generation during olivine carbonation. We designed a sample setup that included a thick-walled cup (made of porous olivine aggregates with a mean grain size of either ∼ 5 or ∼ 80 µm) filled with loose olivine sands with grain sizes of 100–500 µm. The whole sample assembly was reacted with a NaHCO3 aqueous solution at 200 °C, under a constant confining pressure of 13 MPa and a pore pressure of 10 MPa. Using synchrotron-based X-ray microtomography, the three-dimensional (3-D) pore structure evolution of the carbonating olivine cup was documented until the olivine aggregates became disintegrated. The dynamic microtomography data show a volume reduction in olivine at the beginning of the reaction, indicating a vigorous dissolution process consistent with the disequilibrium reaction kinetics. In the olivine cup with a grain size of ∼ 80 µm (coarse-grained cup), dissolution planes developed within 30 h, before any precipitation was observed. In the experiment with the olivine cup of ∼ 5 µm mean grain size (fine-grained cup), idiomorphic magnesite crystals were observed on the surface of the olivine sands. The magnesite shows a near-constant growth throughout the experiment, suggesting that the reaction is self-sustained. Large fractures were generated as the reaction proceeded and eventually disintegrated the aggregate after 140 h. Detailed analysis show that these are expansion cracks caused by the volume mismatch in the cup walls, between the expanding interior and the near-surface which keeps a nearly constant volume. Nanotomography images of the reacted olivine cup reveal pervasive etch pits and wormholes in the olivine grains. We interpret this perforation of the solids to provide continuous fluid access, which is likely key to the complete carbonation observed in nature. Reactions proceeding through the formation of nano- to micron-scale dissolution channels provide a viable microscale mechanism in carbon sequestration practices. For the natural peridotite carbonation, a coupled mechanism of dissolution and reaction-induced fracturing should account for the observed self-sustainability of the reaction.