Systematic understanding and real-time feedback capability for x-ray free electron laser (FEL) accelerator and optical components are critical for scientific experiments and instrument performance. Single-shot wavefront sensing enables characterization of the intensity and local electric field distribution at the sample plane, something that is important for understanding scientific experiments such as nonlinear studies. It can also provide feedback for alignment and tuning of the FEL beam and instrumentation optics, leading to optimal instrument performance and greater operational efficiency. A robust, sensitive, and accurate single-shot wavefront sensor for x-ray FEL beams using single grating Talbot interferometry has been developed. Experiments performed at the Linac Coherent Light Source (LCLS) demonstrate sensitivity and accuracy, both better than , and retrieval of hard x-ray (, ) wavefronts in 3D. Exhibiting high performance from both unfocused and focused beams, the same setup can be used to systematically study the wavefront from the FEL output, beam transport optics, and endstation focusing optics. This technique can be extended for use with softer and harder x rays with modified grating configurations.
Inertial confinement fusion (ICF) holds increasing promise as a potential source of abundant, clean energy, but has been impeded by defects such as micro-voids in the ablator layer of the fuel capsules. It is critical to understand how these micro-voids interact with the laser-driven shock waves that compress the fuel pellet. At the Matter in Extreme Conditions (MEC) instrument at the Linac Coherent Light Source (LCLS), we utilized an x-ray pulse train with ns separation, an x-ray microscope, and an ultrafast x-ray imaging (UXI) detector to image shock wave interactions with micro-voids. To minimize the high- and low-frequency variations of the captured images, we incorporated principal component analysis (PCA) and image alignment for flat-field correction. After applying these techniques we generated phase and attenuation maps from a 2D hydrodynamic radiation code (xRAGE), which were used to simulate XPCI images that we qualitatively compare with experimental images, providing a one-to-one comparison for benchmarking material performance. Moreover, we implement a transport-of-intensity (TIE) based method to obtain the average projected mass density (areal density) of our experimental images, yielding insight into how defect-bearing ablator materials alter microstructural feature evolution, material compression, and shock wave propagation on ICF-relevant time scales.
X-ray free electron lasers (XFELs) provide femtosecond high-power x-ray beams with high spatial coherence, resulting in numerous influential discoveries. Diffractive optics allow for the easy manipulation and measurement of an x-ray beam’s wavefront and enable the realization of complex designed properties and specifications. For example, phase gratings can be used as x-ray beam splitters to enable beam sharing by multiple end stations or in-situ beam monitoring, including spectrum and wavefront measurements. Wavefront preservation and high efficiency and survivability under high power are requirements for such beam splitters. Diamond is the most suitable choice for phase grating fabrication, due to its high thermal conductivity that enables it to survive high average power XFEL beams. We have fabricated a large area (2×2 mm2) high aspect ratio (13:1) diamond grating on a diamond plate. Testing was performed at 9.5 keV and resulted in a high splitting efficiency (30%). Tunable efficiency was obtained via tilting the grating with respect to the x-ray beam. Wavefront fidelity of the split beams were measured to less than λ/100 using a Talbot wavefront sensor.
12 February 2020 in Journal of Synchrotron Radiation
Wavefront sensing at X-ray free-electron lasers is important for quantitatively understanding the fundamental properties of the laser, for aligning X-ray instruments and for conducting scientific experimental analysis. A fractional Talbot wavefront sensor has been developed. This wavefront sensor enables measurements over a wide range of energies, as is common on X-ray instruments, with simplified mechanical requirements and is compatible with the high average power pulses expected in upcoming X-ray free-electron laser upgrades. Single-shot measurements were performed at 500 eV, 1000 eV and 1500 eV at the Linac Coherent Light Source. These measurements were applied to study both mirror alignment and the effects of undulator tapering schemes on source properties. The beamline focal plane position was tracked to an uncertainty of 0.12 mm, and the source location for various undulator tapering schemes to an uncertainty of 1 m, demonstrating excellent sensitivity. These findings pave the way to use the fractional Talbot wavefront sensor as a routine, robust and sensitive tool at X-ray free-electron lasers as well as other high-brightness X-ray sources.
The emergence of X-ray Free Electron Lasers (XFELs) in recent years has opened up new fields of research, with the merging of short wavelengths and ultrafast timescales [1, 2]. As XFEL facilities, ...
The photon spectrum from free-electron laser (FEL) light sources offers valuable information in time-resolved experiments and machine optimization in the spectral and temporal domains. We have developed a compact single-shot photon spectrometer to diagnose soft X-ray spectra. The spectrometer consists of an array of off-axis Fresnel zone plates (FZP) that act as transmission-imaging gratings, a Ce:YAG scintillator, and a microscope objective to image the scintillation target onto a two-dimensional imaging detector. This spectrometer operates in segmented energy ranges which covers tens of electronvolts for each absorption edge associated with several atomic constituents: carbon, nitrogen, oxygen, and neon. The spectrometer’s performance is demonstrated at a repetition rate of 120 Hz, but our detection scheme can be easily extended to 200 kHz spectral collection by employing a fast complementary metal oxide semiconductor (CMOS) line-scan camera to detect the light from the scintillator. This compact photon spectrometer provides an opportunity for monitoring the spectrum downstream of an endstation in a limited space environment with sub-electronvolt energy resolution.