Mark Pankow

Mark Pankow

Auto-generated profile, based on publicly available information

Mark Pankow

Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, NC, USA

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 October 2018
Verified
Report
Closed access
PDF file
RBRory Bigger
Rory Bigger
BBBenoit Blaysat
Benoit Blaysat
CBChristofer Boo
Christofer Boo
MGManuel Grewer
Manuel Grewer
JHJun Hu
Jun Hu
TWThorsten Weikert
Thorsten Weikert

6 June 2016 in Interface Focus
Verified
Journal Article
Open access
PAP. S. L. Anderson
P. S. L. Anderson
JLJ. LaCosse
J. LaCosse
MPM. Pankow
M. Pankow
The use of high-speed puncture mechanics for prey capture has been documented across a wide range of organisms, including vertebrates, arthropods, molluscs and cnidarians. These examples span four phyla and seven orders of magnitude difference in size. The commonality of these puncture systems offers an opportunity to explore how organisms at different scales and with different materials, morphologies and kinematics perform the same basic function. However, there is currently no framework for combining kinematic performance with cutting mechanics in biological puncture systems. Our aim here is to establish this framework by examining the effects of size and velocity in a series of controlled ballistic puncture experiments. Arrows of identical shape but varying in mass and speed were shot into cubes of ballistic gelatine. Results from high-speed videography show that projectile velocity can alter how the target gel responds to cutting. Mixed models comparing kinematic variables and puncture patterns indicate that the kinetic energy of a projectile is a better predictor of penetration than either momentum or velocity. These results form a foundation for studying the effects of impact on biological puncture, opening the door for future work to explore the influence of morphology and material organization on high-speed cutting dynamics.

1 October 2011 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
MPM. Pankow
M. Pankow
ASA. Salvi
A. Salvi
Anthony WaasAnthony Waas
Anthony Waas
CYC.F. Yen
C.F. Yen
SGS. Ghiorse
S. Ghiorse

17 November 2022 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
MPM. Pankow
M. Pankow
MRM. Riosbass
M. Riosbass
BJB. Justusson
B. Justusson
DZD. Zhang
D. Zhang
AWA.M. Waas
A.M. Waas
CYC.F. Yen
C.F. Yen

1 January 2021 in Composite Structures
Verified
Journal Article
Closed access
SJS. Joglekar
S. Joglekar
VRV. Ranatunga
V. Ranatunga
MPM. Pankow
M. Pankow

10 July 2019 in IEEE Sensors Journal
Verified
Journal Article
Closed access
GGGuodong Guo
Guodong Guo
MPMark Pankow
Mark Pankow
KPKara Peters
Kara Peters
This paper presents a fiber Bragg grating (FBG) interrogator based on Vertical Surface Cavity Emitting Lasers (VCSEL). A Fabry-Pérot filter technique is developed to directly calibrate the dynamic wavelength behavior of VCSELs at both low and high sweep rates. A broad bandwidth light source is constructed by multiplexing five VCSELs together to increase the number of FBGs that can be tracked. Scanning of the VCSEL-array is accomplished by a high-speed electronic switch circuit. The developed interrogator achieves a sweep bandwidth of 10 nm at a scanning rate of 4 kHz. Low velocity impact testing of a composite plate with a surface mounted FBG sensor shows that the wavelength detection error was 2.7% when compared with the FBG strain obtained by a high-speed swept laser.