A complete plastic particle mass balance was established at Sweden's second-largest wastewater treatment plant. It comprised material collected at its two bar screens, a 20 mm and a 2 mm one, in the influent water after the 20 mm screen, the effluent water, and the digested sludge. Macro- and microplastics above 500 µm were analysed individually applying ATR-FTIR, while microplastics of 10-500 µm were analysed by µFTIR imaging with automated particle recognition. Masses of plastics >500 µm were determined by weighting, while the mass of the smaller microplastics was estimated from the imaging. The total plastic load on the plant was 202.2 kg d-1, of which the two screens retained 73%. The remaining plastic mass was found in the sludge (13.6%) and the effluent (0.4%). The missing 12.7% could be caused by sampling and measuring uncertainties and potentially also fragmentation below the size detection limit of the analytical approach, or by degradation. The bar screens furthermore retained plastics smaller than the screen size, indicating that this material should be taken into account also when solely looking at smaller particles. The overall treatment efficiency of the plant was high: 99.6% considering both macro- and microplastics, and 98.8% considering only microplastics <500 µm.
Microplastics (MPs) are ubiquitous pollutants in the ocean, and there is a general concern about their persistence and potential effects on marine ecosystems. We still know little about the smaller size-fraction of marine MPs (MPs <300 μm), which are not collected with standard nets for MPs monitoring (e.g., Manta net). This study aims to determine the concentration, composition, and size distribution of MPs down to 10 μm in the Kattegat/Skagerrak area. Surface water samples were collected at fourteen stations using a plastic-free pump-filter device (UFO sampler) in October 2020. The samples were treated with an enzymatic-oxidative method and analyzed using FPA-μFTIR imaging. MPs concentrations ranged between 11 and 87 MP m-3, with 88% of the MPs being smaller than 300 μm. The most abundant shape of MPs were fragments (56%), and polyester, polypropylene, and polyethylene were the dominant synthetic polymer types. The concentration of MPs shows a significant positive correlation to the seawater density. Furthermore, there was a tendency towards higher MPs concentrations in the Northern and the Southern parts of the study area. The concentration of MPs collected with the UFO sampler was several orders of magnitude higher than those commonly found in samples collected with the Manta net due to the dominance of MP smaller size fractions. Despite the multiple potential sources of MPs in the study area, the level of MPs pollution in the surface waters was low compared (<100 MP m-3) to other regions. The concentrations of MPs found in the studied surface waters were six orders of magnitude lower than those causing negative effects on pelagic organisms based on laboratory exposure studies, thus is not expected to cause any impact on the pelagic food web.
The water treatment for microplastics (MP) at a Danish groundwater-based waterworks was assessed by Fourier-Transform IR micro-spectroscopy (μFTIR) (nominal size limit 6.6 μm) and compared to results from Raman micro-spectroscopy (μRaman) (nominal size limit 1.0 μm) on the same sample set. The MP abundance at the waterworks' inlet and outlet was quantified as MP counts per cubic metre (N/m3) and estimated MP mass per cubic metre (μg/m3). The waterworks' MP removal efficiency was found to be higher when analysing by μFTIR (counts: 78.14 ± 49.70%, mass: 98.73 ± 11.10%) and less fluctuating than when using μRaman (counts: 43.2%, mass: 75.1%). However, both techniques pointed to a value of ∼80% for the counts' removal efficiency of MPs >6.6 μm. Contrarily to what was shown by μRaman, no systematic leaking of MPs from the plastic elements of the facility could be identified for the μFTIR dataset, either from the counts (inlet 31.86 ± 17.17 N/m3, outlet 4.98 ± 2.09 N/m3) or mass estimate (inlet 76.30 ± 106.30 μg/m3, outlet 2.81 ± 2.78 μg/m3). The estimation of human MP intake from drinking water calculated from the μFTIR data (5 N/(year·capita)) proved to be approximately 332 times lower than that calculated from the μRaman dataset, although in line with previous studies employing μFTIR. By merging the MP length datasets from the two techniques, it could be shown that false negatives became prevalent in the μFTIR dataset already below 50 μm. Further, by fitting the overall frequency of the MP length ranges with a power function, it could be shown that μFTIR missed approximately 95.7% of the extrapolated MP population (1–1865.9 μm). Consequently, relying on only μFTIR may have led to underestimating the MP content of the investigated drinking water, as most of the 1–50 μm MP would have been missed.
Prior microplastic (MP) research has focused more on the efficiency of removal techniques within wastewater treatment plants (WWTP), with comparatively less emphasis placed on identifying and understanding the sources of MPs. In this study, the presence of MP in wastewater from various sources and their associated WWTPs was investigated. Utilising focal plane array micro Fourier Transform Infrared spectroscopy (FPA-μFTIR), the chemical composition, size distribution, and mass of MPs were quantified. Notably, wastewater generated from an industrial laundry facility exhibited the highest MP concentration of 6900 counts L-1 or 716 μg L-1. Domestic sewage contained MP levels (1534 counts L-1; 158 μg L-1) similar to those at the WWTPs (1640 counts L-1; 114 μg L-1). Polyester was identified as a significant component in most of the sources, predominantly originating from the shedding of fibres during textile washing. Additionally, a post-processing software was employed to compare two methods for fibre identification: aspect ratio and elongation ratio. These findings underscore the potential environmental impact of domestic activities and laundry washing on wastewater MP content.
Retention of microplastics (MPs) at the third largest wastewater treatment plant (WWTP) in Sweden was investigated. The plant is one of the most modern and advanced of its kind, with rapid sand filter for tertiary treatment in combination with mechanical, biological, and chemical treatment. It achieved a significantly high treatment efficiency, which brought the MP concentration in its discharge on par with concentrations measured in marine waters of the same region. This novel data shows that properly designed modern WWTPs can reduce the MP content of sewage down to background levels measured in the receiving aquatic environment. Opposite to current understanding of the retention of MP by WWTPs, a modern and well-designed WWTP does not have to be a significant point source for MP. MPs were quantified at all major treatment steps, including digester inlet and outlet sludge. MPs sized 10-500 µm were analyzed by a focal plane array based micro-Fourier transform infrared (FPA-µFTIR) microscopy, a hyperspectral imaging technique, while MPs above 500 µm were analyzed by Attenuated Total Reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. Mass was estimated from the hyperspectral images for MPs 500 µm. The overall treatment efficiency was in terms of MP counts 99.98 %, with a daily input of 6.42 × 1010 and output of 1.04 × 107 particles. The mass removal efficiency was 99.99 %. The mechanical part of the treatment, the pre-treatment, and primary stages, reduced both the MP counts and mass by approximately 71 %. The combined biological treatment, secondary settling, and final polishing with rapid sand filtration removed nearly all the remaining 29 %. MPs became successively smaller as they passed the different treatment steps. The digester inlet received 1.04 × 1011 MPs daily, while it discharged 9.96 × 1010 MPs, causing a small but not significant decrease in MP counts, with a corresponding MP mass reduction of 9.56 %.
Studies on the environmental impact of nanoplastics face challenges in plastic analysis and a scarcity of nanoplastic materials necessary for the development of analytical techniques and experiments on biota impact. Here we provide detailed procedures for obtaining nanoparticles suspended in water for the most commonly used polymers: Polypropylene (PP), Polyvinylchloride (PVC), Low- and High-Density Polyethylene (PE-LD, PE-HD), and Polystyrene (PS). We dissolved larger size material to reprecipitate nanoparticles. For all plastic types, we obtained nanoparticles with a size between 50 and 300 nm, and a mainly spherical morphology. We verified that no irreversible agglomeration or coalescence of the particles occurred after 5 days of storage. The concentrations obtained in the final carrier solution were of the order of 109 particles mL−1. To prevent the persistence of reagents in the final carrier solution, a filtration step was implemented at the end of the process. The method proved unsuitable for Polyethylene Terephthalate (PET).