We describe a distributed baseband amplifier using a new loss compensation technique for the drain artificial line. The new loss compensation circuit improves a high-frequency performance of the amplifier and makes the gain bandwidth product of the amplifier larger than that of conventional ones. We also use dc matching terminations and dumping resistors for the gate and drain artificial lines to obtain flat gain from frequencies as low as 0 Hz. One IC fabricated using 0.1 /spl mu/m-gatelength InAlAs/InGaAs/InP HEMTs has a gain of 16 dB over a 0-to-50 GHz band, resulting in a gain bandwidth product of about 300 GHz. Another IC has a gain of 10 dB over a 0-to-90 GHz band. These are the highest gain bandwidth product and the widest band reported for baseband amplifier ICs applicable to optical transmission systems.
The burst-mode 3R receiver using monolithic ICs for 10-Gbit/s-class optical access networks is reported. In a point-to-multipoint access system like a passive optical network (PON), the receiver at the optical line terminal (OLT) must be able to handle burst-mode optical packets with significantly different powers and phases. An OLT receiver with high sensitivity with instantaneous response to burst inputs is desired for widening the accommodation area and for high efficiency in PON uplinks. Currently, the diffusion of high-speed Internet connection services represented by fiber to the home services at 1.25 Gbit/s is remarkable and the standardization of the next-generation system operating at 10 Gbit/s has started in IEEE. We first discuss the issues in the implementation of 10-Gbit/s-class PON systems, focusing on securing the accommodation area and the quality of the service comparable with those of the deployed system. Against that background, we propose target specifications for sensitivity, a dynamic range and response speed of the 10-Gbit/s-class burst-mode receiver so as to secure the power budget and the upstream efficiency comparable with those of the already-installed systems. Our burst-mode 3R receiver was designed to meet the above requirements and developed using monolithic ICs of transimpedance amplifier, limiting amplifier, and clock and data recovery circuit fabricated by using SiGe BiCMOS technologies along with a p-i-n photodiode. High sensitivity of , a wide dynamic range of over 16.5 dB, and quick response time of 75 ns were confirmed for burst inputs with extremely different powers.
An InAlAs/InGaAs/InP HEMT distributed baseband amplifier IC that uses a new loss compensation technique for the drain artificial line is described. The amplifier IC has a gain of 10 dB with a 0–90 GHz bandwidth. This is the widest bandwidth among all reported baseband amplifier ICs to date.
1 December 1994 in IEEE Journal of Solid-State Circuits
A DC-60 GHz, 9 dB distributed amplifier IC module is fabricated with 0.15 /spl mu/m InAlAs-InGaAs low-noise HEMTs with 155 GHz f/sub T/ and 234 GHz f/sub max/. The device is mounted in a metal package with 1.8 mm coaxial cable signal interfaces. The package is specially designed using three-dimensional electromagnetic field analyses, resulting in very flat frequency characteristics of the module within 1.5 dB gain ripples over the entire bandwidth. A multichip module loaded with two amplifier ICs in cascade is also fabricated, and operates at a 17.5 dB gain from 60 kHz to 48 GHz. The 1 dB gain compression output power is about 5 dBm for both modules. The noise figure of the single-chip module is approximately 4 dB over a 10-40 GHz frequency range.<>
13 February 2006 in Journal of Lightwave Technology
This paper proposes a new single-fiber 10-Gb/s optical loopback method for wavelength-division-multiplexing (WDM) optical access networks. The proposed method improves the tolerance of backreflection that causes interferometric crosstalk with the loopback method on a single fiber. Furthermore, bit synchronization is used to avoid the problem of wavelength dispersion caused in optical access networks. The authors simulated the available distance, received eye patterns at 10 Gb/s, and confirmed the excellent eye opening. 10-Gb/s back-to-back experiments show that the proposed method provides a 17-dB improvement in backreflection tolerance compared with the direct method. The paper reports the first successful results for 10- and 20-km transmission experiments using a standard single-mode optical fiber. The measured eye patterns agreed well with the simulation results. The paper also shows measured bit-error rates (BERs) equivalent to those of a back-to-back configuration.
An ac-coupled burst-mode receiver (B-Rx) for 10-Gbit/s class PON systems that uses a novel baseline-wander common-mode-rejection (BLW-CMR) technique and an inverted distortion technique is proposed and demonstrated. The realization of 10-Gbit/s class PON systems requires the development of a B-Rx with high sensitivity, a wide dynamic range, and a fast response for handling the burst-mode data. The BLW-CMR technique can cancel out the transient responses of capacitors at an ac-coupled interface, and the inverted distortion technique can reduce the duty-cycle distortion caused by the reference voltage wandering at long consecutive identical digits (CIDs) with a fast average detector. A B-Rx using these techniques can realize high receiver sensitivity, a wide dynamic range, and an instantaneous response with a high tolerance to CIDs. We achieved a settling time of less than 150 ns, a sensitivity of -29.8 dBm, and a dynamic range of 24.8 dB at a bit error rate of 10- 3 with a 231-1 pseudo random bit sequence for a burst-mode optical input at 10.3125 Gbit/s.