28 March 2022 in IEEE Transactions on Geoscience and Remote Sensing
Gravity measurement is an important geophysical prospecting method for mineral exploration. With most of the shallow ore deposits in China being exploited, the future targets for exploration will be aimed at the deep mineral resources about 4-km underground. To improve the resolving ability in the vertical direction of the 3-D density inversion to find deep-source minerals, we propose to achieve the inversion of gravity anomalies by combining power-spectrum derived adaptive weighting and cross-gradient regularization. First, spectral analysis is utilized to conduct the source-depth separation, and the adaptive weighting function is designed depending on the slope of the radial logarithmic power spectrum of the gravity anomaly, which can enhance the correspondence for the field sources with different depths to improve the vertical resolution relatively. Thus, each separated source with different depths could be given an adaptive weighting coefficient in each separated inversion. Second, the cross-gradient technique is introduced as a structural constraint in the objective function to further constrain the separated inversion process. By performing two-cuboid-source cases, it can be seen that this combination calculated approach has great potential to improve the quality of the inversion results. When examining the inversion of the actual gravity data from certain ore district in the west of Zhen’an, South Qinling, we speculate that a potential deep ore body would exist in the deposit via utilizing the recovered density model obtained by the proposed method.
22 July 2024 in IEEE Transactions on Geoscience and Remote Sensing
The three-direction magnetization intensities of a source can be obtained by the magnetization vector inversion (MVI) of magnetic data, and therefore MVI can be well applied to a magnetic anomaly with remanence. However, MVI exhibits poor applicability attributed to its low computational efficiency for a data with large area and undulating terrain. We proposed a discrete function (DF) method to improve the efficiency of MVI, which is suitable for uniform hexahedron mesh and unstructured tetrahedral mesh. In this method, DF was used to fit the magnetization vectors of a given number of cells, and the computation of the physical properties of the cells was replaced by the computation of function coefficients, and the memory and calculation time were reduced, as the number of function coefficients was less than the number of cells. The Gramian constraint item in MVI could be directly computed by function coefficients without increasing the computation process. For uniform hexahedron mesh, the integration of DF with block-Toeplitz-Toeplitz-block-fast Fourier transform (DF–BTTB-FFT) method can further improve the inversion efficiency. The model tests revealed that the DF method could reduce the storage and computation time by approximately five times without precision loss, and DF – BTTB-FFT method could achieve approximately four times improvement compared with DF method. Finally, the proposed DF method was used to accomplish the MVI of real magnetic anomaly and its gradient data in Shaanxi Province to delineate the range of the subsurface burned zone, and the distribution was ascertained by combining the nuclear magnetic water measurements.
24 August 2021 in Geophysics
The density inversion of gravity data is commonly achieved by discretizing the subsurface into prismatic cells and calculating the density of each cell. During this process, a weighting function is introduced to the iterative computation to reduce the skin effect during the inversion. Thus, the computation process requires a significant number of matrix operations, which results in low computational efficiency. We have adopted a density inversion method with nonlinear polynomial fitting (NPF) that uses a polynomial to represent the density variation of prismatic cells in a certain space. The computation of each cell is substituted by the computation of the nonlinear polynomial coefficients. Consequently, the efficiency of the inversion is significantly improved because the number of nonlinear polynomial coefficients is less than the number of cells used. Moreover, because representing the density change of all of the cells poses a significant challenge when the cell number is large, we adopt the use of a polynomial to represent the density change of a subregion with fewer cells and multiple nonlinear polynomials to represent the density changes of all prism cells. Using theoretical model tests, we determine that the NPF method more efficiently recovers the density distribution of gravity data compared with conventional density inversion methods. In addition, the density variation of a subregion with 8 × 8 × 8 prismatic cells can be accurately and efficiently obtained using our cubic NPF method, which also can be used for noisy data. Finally, the NPF method is applied to real gravity data in an iron mining area in Shandong Province, China. Convergent results of a 3D perspective view and the distribution of the iron ore bodies are acquired using this method, demonstrating the real-life applicability of this method.