29 May 2020 in IEEE Access
This paper presents some theoretical considerations and experimental results regarding the problem of maximum power extrapolation for the assessment of the exposure to electromagnetic fields radiated by 5G base stations. In particular the results of an extensive experimental campaign using an extrapolation procedure recently proposed for 5G signal is discussed and experimentally checked on a SU-MIMO signal. The results confirm the effectiveness of the extrapolation technique. Starting from an analysis (that represents a further novel contribution of this paper) on the impact of Spatial Division Multiple Access techniques used in 5G on the measurement of EMF level, some indications of possible extension of the technique to the highly complex MU-MIMO case are also given.
21 January 2022 in IEEE Access
Maximum-Power Extrapolation (MPE) for mobile telecommunication sources follows an established paradigm based on the identification and measurement of a channel that acts as a power reference. Prior to the 5G era, the role of reference channel has been played by always-on broadcast signals since they had the great advantage of being always transmitted at the maximum power level allowed for a generic signal channel. However, the beamforming implemented by 5G sources obliges us to rethink this approach. In fact, with beamforming the 5G source can transmit data traffic streams through a beam characterized by a much higher gain than the broadcast one. This implies that the detected power for traffic beams could be much higher than the corresponding power of broadcast beams. In this paper, a novel approach for 5G MPE procedure is presented, where the direct measurement of the received power of a traffic beam is used to assess the maximum exposure generated by a 5G system. An innovative specific experimental setup is also proposed, with the use of a User Equipment (UE) with the aim of forcing the traffic beam toward the measurement positions. In this way, it is possible to directly measure the power of each Resource Element (RE) transmitted by the traffic beam. As opposed to other MPE proposals for 5G, the discussed technique does not require any correction of the measured data since it relies only on the traffic beam pointing toward the measurement position, simplifying the overall MPE procedure and thus reducing the uncertainty of the MPE estimated field strength.
18 September 2020 in IEEE Access
The fifth-generation (5G) New Radio (NR) cellular network has been launched recently. The assignment of new spectrum bands and the widespread use of Massive MIMO (MaMIMO) and beamforming techniques for better radio coverage are two major features of the new architecture. They imply both opportunities and challenges, one of the most daring one among the latter ones is the research for methods to assess human exposure to electromagnetic fields radiated by the base stations. The long-term time-varying behavior and spatial multiplexing feature of the MaMIMO antennas, along with the radio resource utilization and adoption of Time-Division Duplexing (TDD), requires that the assessment of exposure to electromagnetic fields radiated by 5G systems is based on a statistical approach that relies on the space and time distribution of the radiated power. That, in turn, is determined through simulations based on the actual maximum transmitted power – defined as the 95th percentile of the empirical distribution obtained from historical data of radiated power – rather than on the nominal one. To ensure that exposure limits are never exceeded, a monitoring and control system (usually referred to as Power Lock (PL)) that limits the transmitted power can be used. In this paper we propose a methodology, independent from the specific technical solution implemented by the manufacturer, to characterize such control systems and determine their capability to limit the average power transmitted over a given time interval to a value that keeps the corresponding average exposure to electromagnetic fields below a specified value. Experimental results show the effectiveness of the methodology and that it can also be used to identify when the PL interacts with the higher levels of the MaMIMO system architecture.
28 February 2017 in IEEE Wireless Communications
ARAlessandro E. C. Redondi
The exponential growth of mobile traffic is forcing operators to quickly increase the capacity of their networks by means of new technologies and advanced architectures. This capacity expansion not only brings increasing fixed costs for additional network infrastructures, but also inflates operational costs, which are becoming critical, mainly in terms of energy bills. In this perspective, monitoring the energy consumption of network devices and defining their energy profile models are valuable approaches for estimating energy costs and identifying the most efficient configurations. In this article, we propose an energy profiling approach that simplifies the characterization of different base station components and allows the estimation of the network energy efficiency relying only on traffic statistics. We have validated the approach over the extensive dataset of real measurements provided by a probe network for monitoring live energy consumption of Vodafone sites in three different countries.
11 September 2024 in IEEE Transactions on Instrumentation and Measurement
We present a methodology for on-site zero-span (ZS) measurement of incident power generated by 5G base stations that operate at millimeter-waves (mm-waves), analyzing the challenges offered by the new frequency band and Non-Line-of-Sight (NLoS) propagation, which is the most common situation for mobile network users. We also investigate the impact of omnidirectional and directional measurement antennas. This is the first research on this topic available in scientific literature. Our results reveal that the measurement method designed for frequencies below 6 GHz in Line-of-Sight (LoS) conditions is also applicable in the mm-wave range. At the same time, in NLoS, mitigation strategies are suggested to measure signals accurately. That is, an omnidirectional antenna is recommended since a directional one requires an initial assessment to align the probe with the direction of the strongest signal. Additionally, directional antennas under NLoS conditions don’t guarantee that the power density coming from different directions due to reflections is measured entirely. This study holds significant importance for international standardization bodies focusing on establishing measurement methods to evaluate exposure originating from mobile network base stations.