Mohammed D. Abdulnafaa

Mohammed D. Abdulnafaa

Auto-generated profile, based on publicly available information

Mohammed D. Abdulnafaa

Department of Environmental Engineering, College of Engineering, University of Mosul, Mosul, Iraq

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 May 2021 in Transportation Infrastructure Geotechnology
Verified
Journal Article
Closed access
PDF file
MAMoataz A. Al-Obaydi
Moataz A. Al-Obaydi
MAMohammed D. Abdulnafaa
Mohammed D. Abdulnafaa
OAOrhan A. Atasoy
Orhan A. Atasoy
Ali Firat CabalarAli Firat Cabalar
Ali Firat Cabalar

21 June 2021 in Soils and Rocks
Verified
Journal Article
Closed access
MAMohammed Abdulnafaa
Mohammed Abdulnafaa
MAMuwafaq Awad
Muwafaq Awad
Ali Firat CabalarAli Firat Cabalar
Ali Firat Cabalar
NANurullah Akbulut
Nurullah Akbulut
BOBurak Ozufacik
Burak Ozufacik
The study aims to investigate the effects of three different construction and demolition materials (CDMs), including crushed waste asphalt (CWA), crushed waste bricks (CWB), and crushed waste concrete (CWC), on some geotechnical properties of low plastic clayey soil, particularly, the undrained shear strength (Su) and the hydraulic conductivity (k). A set of experimental tests were performed on clayey soil and on clayey soil-CDM mixtures at mixing ratios of 5%, 10%, 15%, and 20% by dry weight. The results show that the soil plasticity decreases as the CDMs increase. Quantitatively, it is found a maximum of 12%, 6%, and 6% decrease in the liquid limits (LL) and a maximum of 9%, 4%, and 6% decrease in the plasticity limit (PI) of the mixtures with 20% of CWA, CWB, and CWC, respectively. The results of the Su estimated empirically from the fall cone tests show that the Su decreases as the CDMs increase. The Su reduces by approximately 10% and 2% of the mixtures with 20% CWA and CWB, respectively. But the Su is not affected by the CWC additive for water content lower than approximately 35%. The k value increases as the CDMs increase. The results show that the reported k value increases by 75%, 79%, and 247% of the mixtures with 20% of CWA, CWB, and CWC, respectively. Additionally, the k values obtained from the consolidation test confirm the findings of the effect of the CDMs on the coefficient of hydraulic conductivity.

1 April 2020 in Ingeniería e Investigación
Verified
Journal Article
Open access
PDF file
Ali Firat CabalarAli Firat Cabalar
Ali Firat Cabalar
HGHayder Govar
Hayder Govar
MAMohammed D. Abdulnafaa
Mohammed D. Abdulnafaa
HIHaluk Isik
Haluk Isik
This paper aims to investigate the use of spiral aluminum computer numerical control milling waste (CNC-W) in the construction of road pavement subgrade. The soil (CL) was mixed with CNC-W spirals with ratios of between 0% and 20%, and 5 percent increments by dry weight with different water contents. California Bearing Ratio (CBR), Unconfined Compressive Strength (UCS), and consolidation tests were conducted. The experimental results indicated that the inclusion of CNC-W spirals increased the CBR value of clay up to the 15% mixture ratio, then decreased it. Similarly, the UCS value of clay was increased to the same ratio, whilst the UCS was not able to be determined due to the failing of all specimens with a mixture ratio higher than 15%. The permeability and swelling values, as well as the consolidation characteristics of the mixtures, were defined. The swelling percentages decreased from 1,15 cm/sec to 0,81 cm/sec with an increment in the CNC-W spiral content. A reduction was observed in the coefficient of permeability (k) values up to 15% mixture ratio, whilst it remained constant with change in CNC-W spiral content with a 20% mixture ratio. Coefficient of consolidation demonstrated a similar pattern of behavior to the permeability changes.

31 May 2021 in Transportation Infrastructure Geotechnology
Verified
Journal Article
Open access
PDF file
MAMoataz A. Al-Obaydi
Moataz A. Al-Obaydi
MAMohammed D. Abdulnafaa
Mohammed D. Abdulnafaa
OAOrhan A. Atasoy
Orhan A. Atasoy
Ali Firat CabalarAli Firat Cabalar
Ali Firat Cabalar
A Correction to this paper has been published: https://doi.org/10.1007/s40515-021-00176-5

3 April 2025 in Engineering, Technology & Applied Science Research
Verified
Journal Article
Open access
PDF file
MAMohammed D. Abdulnafaa
Mohammed D. Abdulnafaa
AAAbdulnasser Y. Alshuwaykhi
Abdulnasser Y. Alshuwaykhi
AAAymen W. Al-Dabbagh
Aymen W. Al-Dabbagh
The current research investigates the residual shear strength of clay soils to which different percentages (5, 10, 15, and 20%) of sand are added, playing a pivotal role in determining the stability of steep slopes on these soils. The residual shear strength was compared with the shear strength calculated from the direct shear test and the unconfined compression strength test. According to the results, the clay soil’s swelling ranged from medium to high, and its engineering characteristics were similar to that of all clay soils found in most sloped areas and hills in Mosul city. Also, a notable reduction was observed in the plasticity index with an increase in the sand percentage. In the residual shear test, a rise in shear coefficients (effective angle of internal friction (Φ') and cohesion(c')) was demonstrated with an increase in the percentage of sand addition up to a certain limit (15%), which is the same percentage that gave values for (c and Φ) in the direct shear test.

1 March 2022 in Al-Rafidain Engineering Journal (AREJ)
Verified
Journal Article
Open access
PDF file
AAAbdulrahman Hani Aldaood
Abdulrahman Hani Aldaood
IAIbrahim M. Al-Kiki
Ibrahim M. Al-Kiki
MAMohammed D. Abdulnafaa
Mohammed D. Abdulnafaa
This review evaluates industrial waste: its definition, components and types, and then its impact on the soil. the remarkable ‌development in industry in recent times and its progression forward led to more secondary products, which at present ‌constitute one of the most important problems facing the scientist. The researchers discuss the extent to which they can be ‌used in soil stabilization by reviewing most of the research and studies on industrial waste and soil. In addition, the ‌advantages and disadvantages of using industrial waste in treating soil problems at the lowest possible cost without ‌resorting to other alternatives. This paper also presents the role of society in reducing its environmental damage by ‌reviewing researches and studies on recyclable materials and the most applicable at present by the industry, which is a ‌suitable idea to incorporate the best-recycled materials in the construction of roads and engineering facilities. These steps ‌came after taking the processes of recycling and reusing industrial waste in many forms and methods, and according to the ‌nature and type of waste and the purpose of its reuse, in addition to the state and nature of the material with which these ‌wastes are used.‌