J. Gerard Schepers

J. Gerard Schepers

Auto-generated profile, based on publicly available information

J. Gerard Schepers

ECN, Westerduinweg 3, 1755 LE Petten, The Netherlands

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 January 2018 in Wind Energy Science
Verified
Journal Article
Open access
PDF file
IHIván Herráez
Iván Herráez
EDElia Daniele
Elia Daniele
JSJ. Gerard Schepers
J. Gerard Schepers
The analysis of wind turbine aerodynamics requires accurate information about the axial and tangential wake induction as well as the local angle of attack along the blades. In this work we present a new method for obtaining them conveniently from the velocity field. We apply the method to the New Mexico particle image velocimetry (PIV) data set and to computational fluid dynamics (CFD) simulations of the same turbine. This allows the comparison of experimental and numerical results of the mentioned quantities on a rotating wind turbine. The presented results open up new possibilities for the validation of numerical rotor models.

18 June 2018 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
JSJ.G. Schepers
J.G. Schepers
KBK. Boorsma
K. Boorsma
NSN. Sørensen
N. Sørensen
VOVoutsinas
Voutsinas
GSG Sieros
G Sieros
JMJ. Madsen
J. Madsen
This paper presents final results from the EU project AVATAR in which aerodynamic models are improved and validated for wind turbines on a scale of 10 MW and more. Special attention is paid to the improvement of low fidelity engineering (BEM based) models with higher fidelity (CFD) models but also with intermediate fidelity free vortex wake (FVW) models. The latter methods were found to be a good basis for improvement of induction modelling in engineering methods amongst others for the prediction of yawed cases, which in AVATAR was found to be one of the most challenging subjects to model. FVW methods also helped to improve the prediction of tip losses. Aero-elastic calculations with BEM based and FVW based models showed that fatigue loads for normal production cases were over predicted with approximately 15% or even more. It should then be realised that the outcome of BEM based models does not only depend on the choice of engineering add-ons (as is often assumed) but it is also heavily dependent on the way the induced velocities are solved. To this end an annulus and element approach are discussed which are assessed with the aid of FVW methods. For the prediction of fatigue loads the so-called element approach is recommended but the derived yaw models rely on an annulus approach which pleads for a generalised solution method for the induced velocities.

30 September 2016 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
JCJ.G. Schepers O. Ceyhan
J.G. Schepers O. Ceyhan
KBK. Boorsma
K. Boorsma
AGA. Gonzalez
A. Gonzalez
XMX Munduate
X Munduate
OPOscar Pires
Oscar Pires
ACA. Croce
A. Croce
This paper presents the most recent results from the EU project AVATAR in which aerodynamic models are improved and validated for wind turbines on a scale of 10 MW and more. Measurements on a DU 00-W-212 airfoil are presented which have been taken in the pressurized DNW-HDG wind tunnel up to a Reynolds number of 15 Million. These measurements are compared with measurements in the LM wind tunnel for Reynolds numbers of 3 and 6 Million and with calculational results. In the analysis of results special attention is paid to high Reynolds numbers effects. CFD calculations on airfoil performance showed an unexpected large scatter which eventually was reduced by paying even more attention to grid independency and domain size in relation to grid topology. Moreover calculations are presented on flow devices (leading and trailing edge flaps and vortex generators). Finally results are shown between results from 3D rotor models where a comparison is made between results from vortex wake methods and BEM methods at yawed conditions.

1 September 2001 in Wind Engineering
Verified
Journal Article
Closed access
GSGerard Schepers
Gerard Schepers
RBRebecca J Barthelmie
Rebecca J Barthelmie
KRKostas Rados
Kostas Rados
BLBernhard Lange
Bernhard Lange
WSWolfgang Schlez
Wolfgang Schlez

1 October 2004 in Wind Energy
Verified
Journal Article
Closed access
PDF file
JSJ. G. Schepers
J. G. Schepers
LFL. Feigl
L. Feigl
RRR. van Rooij
R. van Rooij
ABA. Bruining
A. Bruining

12 July 2005 in Journal of Solar Energy Engineering
Verified
Journal Article
Closed access
PDF file
RRR. P. J. O. M. van Rooij
R. P. J. O. M. van Rooij
JSJ. G. Schepers
J. G. Schepers
The effect of rotation has been investigated with emphasis on the impact of blade geometry on the “correction factor” in stall models. The data used came from field tests and wind tunnel experiments performed by the National Renewable Energy Laboratory and were restricted to the steady-state nonyawed conditions. Three blade layouts were available; a blade with constant chord without twist (phase II), a blade with constant chord and twist (phases III and IV), and a tapered blade with twist (phase VI). Effects due to twist and taper were determined from comparison of c n between the different blade layouts. The formulation of the stall model was rewritten so that the measured c n values could be used without reference to 2D airfoil performance. This enabled a direct comparison of the normal force characteristics between the four blade stations of the selected blade configurations. In particular, the correction term f used in stall models for rotational effects was analyzed. The comparison between the test results with a straight and a twisted blade showed that a relation for twist + pitch is required in f . In addition, a dependency offon the angle-of-attack was identified in the measurements and it is recommended that this dependency be incorporated in the stall models.