1 March 2023 in Turkish Journal of Civil Engineering
Bu çalışmada, %50 ve %85 olmak üzere, iki farklı rölatif sıkılığa sahip kum zeminde 40 adet model test deneyi yapılmıştır. Model temel sistemleri; uygulanan yükün, sadece radyeye, sadece kazıklara ve kazıklı radye temel sistemine taşıtıldığı durumlar dikkate alınarak oluşturulmuştur. Kazıklı radye temeller radyenin zemine gömülü olduğu ve zemine gömülü olmadığı iki farklı durum için irdelenmiştir. Eksenel statik artımsal yükler altında analiz edilen modellerde; optimum kazık aralığının radyenin gömülü olmadığı durumda daha küçük, gömülü olduğu durumda ise daha büyük S/D oranına sahip olduğu belirlenmiştir. Optimum kazık aralığı, orta sıkı zeminde, 1.5D ile 4D, çok sıkı zeminde 4.5D ile 6D arasında bulunmuştur.
1 June 2022 in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Piled foundation design and behaviour under static and dynamic loading (wave motion, earthquake, wind, vibration loadings of machinery) conditions are study subjects that are focus of interest recently in the geotechnical engineering applications. Liquefaction can be described as strength and stiffness loss of a loose, saturated non-cohesive soil under undrained cyclic loading as a result of increasing pore water pressures which reduce effective stress. Large deformations and lateral flow occurring in the layers of liquefied soil during earthquake could lead to strength and stiffness lose which may result with pile buckling and considerably increased earthquake damage on the superstructure. Predicting the bearing capacity and the deformation shape of the piled foundations during the earthquake is essential for the economy and the structural safety of the design. In this study model pile tests are conducted in uniform sandy soil and pile structural capacity is investigated under the effects of relative density and degree of saturation of surrounding soil, and pile embedment depth. Steel rods were used to represent the piles in the model tests. Sand soil was placed in a cylindirical tank at different thicknesses to provide for different pile embedment depths. Soils were compacted at four different compaction level to provide relative densities in the range of 45-80%. Static incremental load has been applied on the upper plate of the pile system in the tests. While the increase in the relative density affects the structural capacity of the piles positively, surrounding soil being saturated has resulted with capacity losses. Experimental results show that there is a consistency between our experimental findings and literature about deformation shape and buckling length of piles in liquified soils.
31 March 2024 in Bilge International Journal of Science and Technology Research
The properties of the soils in terms of engineering must be identified for the design of buildings and foundations to be constructed in areas where soft clay or loose sand ground conditions predominate. The engineering properties of different soils diversify in a broad range based on the sort of the ground in addition to the terrain conditions like the degree of compaction, water content, consolidation pressure, loading, and drainage conditions. Grounds may not perpetually hold the desired properties. Thanks to the structures to be built on the grounds, excessive settlements or collapses can happen because of inadequate ground bearing capacity. In order to reinforce the weaknesses of the soils, either the application of a deep foundation should be employed, or a proper improvement method should be applied to the foundation ground.In the study, the effect of the reinforcement of the geotextile, which has become widespread, on the clay ground was examined. Experiments have been conducted to identify the index properties, settlement, and sliding resistance parameters of soils on Süleyman Demirel University Soil Mechanics Laboratory on clay samples from the provinces of İzmir and İstanbul. Following the identification of the settlement and sliding values, the geotextile was added, and its effect on the settlement and bearing strength values was analyzed. Experiments were conducted by placing single-layered and double-layered geotextile in the samples with the values of optimum water content, the water content 10% more than the optimum value, and the water content 10% less than the optimum value.The results achieved after laboratory experiments are displayed with graphics and compared with each other.
31 December 2024 in Journal of Innovations in Civil Engineering and Technology
In pile foundation systems, displacements in important structures affected by both axial and lateral loads must be limited within elastic limits. For elastic limits; effects of the important parameters such as; pile diameter, pile spacing, pile length /pile diameter ratio and relative density were examined. For this purpose, loadings were carried out in medium-dense and extreme dense sand conditions with the following parameter considerations: pile length/pile diameter ratios of 10, 15 and 30, pile spacings of 3D and 6D and for relative density of the soil 50% and 85%. By determining the vertical and lateral displacements of the pile foundation system formed under axial and lateral load effects and loading related ground stresses, the relationship between the foundation system and the ground was expressed. Experimental data were analyzed in Plaxis 3D. From the results of the performed model tests and Plaxis 3D optimum design parameters have been determined for soil-structure interaction in lateral loaded pile foundation systems.
31 March 2024 in Bilge International Journal of Science and Technology Research
Sea transport is preferred because it is safe and economical in countries in the regions that dominate world trade. Approximately 86% of the developing and increasing trade volume is provided by sea transportation. Ports, which are an important pillar of international trade, take an active place in the transportation network for these reasons. In our country, an increase has been observed in the studies on the design of coastal port structures in the last 15 years. In the design of coastal structures, technical approaches and durability are at the forefront, while recently the continuity of the performance of the structures has been taken as a basis. They are exposed to static and dynamic loads throughout their service life. In order to encounter minimum damage due to earthquake effects, an analysis that reflects the behavior under static and dynamic loads and the parameters must be determined correctly. For this purpose, parameter changes were investigated to examine the dynamic behavior of a scaffolding structure. Piles diameters of 600, 800 and 1000 mm and placement spacing of 4D and 8D were considered variable. Analyzes were carried out with Sap 2000, a finite element program. The capacity of the building was determined with pushover analysis and its dynamic performance was evaluated with time history analysis.