Analysis of the sedimentary architecture of the early Billefjorden Trough, an exceptionally well-exposed Carboniferous half-graben located in Svalbard, Arctic Norway, allows detailed reconstruction of fault development and basin geometry. Sedimentary facies distribution reveals facies variability in an early synrift fill, when an array of meso-scale intra-basinal faults segmented the basin into rotated blocks with differential subsidence. Growth of these faults into larger systems impacted the distribution of accommodation space and the drainage pattern expressed in fluvial and deltaic sandstone-dominated units. An axially back-stepping character of the early synrift facies associations (Stages 1–3) is reflected in aggrading homogenous facies types of continental depositional Stage 1, which evolved into back-stepping facies belts of deltaic to nearshore depositional environment, Stages 2 and 3, due to the opening of a connection to the sea. The drainage pattern and accommodation distribution in the early synrift deposits reflect a relatively symmetrical basin that predates a later prominent half-graben configuration of the basin. Supplementary material: Figures presenting lithostratigraphic columns of the well data (Supplementary material 1), location of logs in Ragnardalen (Supplementary material 2) and geological map used in Figure 2b (Supplementary material 3) are available at https://doi.org/10.6084/m9.figshare.c.4293077
The Svalbard Composite Tectono-Sedimentary Element (SCTSE) is located on the northwestern corner of the Barents Shelf and comprises a Carboniferous–Pleistocene sedimentary succession. Due to Cenozoic uplift, the succession is subaerially exposed in the Svalbard archipelago. The oldest parts of the succession consist of Carboniferous–Permian mixed siliciclastic, carbonate and evaporite, and spiculitic sediments that developed during multiple phases of extension. The majority of the Mesozoic succession is composed of siliciclastic deposits formed in sag basins and continental platforms. Episodes of Late Jurassic and Early Cretaceous contraction are evident in the eastern part of the archipelago and in nearby offshore areas. Differential uplift related to the opening of the Amerasian Basin and the Cretaceous emplacement of the High Arctic Large Igneous Province created a major hiatus spanning from the Late Cretaceous and early Danian throughout the Svalbard CTSE. The West Spitsbergen Fold and Thrust Belt and the associated foreland basin in central Spitsbergen (Central Tertiary Basin) formed as a response to the Eurekan Orogeny and the progressive northward opening of the North Atlantic during the Paleogene. This event was followed by the formation of yet another major hiatus spanning the Oligocene–Pliocene. Multiple reservoir and source-rock units exposed in Svalbard provide analogues to the prolific offshore acreages in the SW Barents Sea, and are important for the de-risking of plays and prospects. However, the archipelago itself is regarded as a high-risk acreage for petroleum exploration. This is due to Paleogene contraction and late Neogene uplift of the western and central parts in particular. There is an absence of mature source rocks in the east, and the entire region is subjected to strict environmental protection.
Fault‐controlled mixed siliciclastic‐carbonate‐evaporite depositional systems exhibit distinct sensitivity to tectonic and eustatic controls that are expressed in the sedimentary architecture. In the Upper Carboniferous Billefjorden Trough (Svalbard, Norway), up to 2,000 m of a warm and arid climate syn‐rift basin fill comprises such depositional systems, documented in this study with traditional field techniques supported by helicopter‐ and ground‐based LIDAR models. The basin evolved from siliciclastics‐dominated red beds and paralic units that filled a symmetrical basin, to a rift climax half‐graben with alluvial fans entering the basin along relay ramps of the master fault zone (Billefjorden fault zone). Faults located in the hanging wall dip‐slope prevented the progradation of coarser material to the eastern part of the basin. Later, structural reorganisation in the dipslope led to the cessation of easternmost faults with deformation focusing along one major lineament (Løvehovden fault zone) antithetic to the master fault zone. The basin subsidence became more symmetrical, with main central depocentre and shallower platforms near the basin flanks. Footwall anticlines from faults displacement gradients were sensitive to periodical exposure and recorded dissolution breccias and footwall synclines preserved evaporites coupled with shallow marine siliciclastic deposits. Concurrently, thick gypsum/anhydrite deposits in the basin centre reflect glacio‐eustatic lowstands, whereas evenly thick carbonate deposition characterises highstands. While most analysis of syn‐rift basin fill is based on siliciclastics deposits, we here demonstrate the complexity of tectonism versus eustatic sea level changes in a mixed carbonate‐evaporite syn‐rift deposits. Tectonic influence is ascribed to the deposition of alluvial fans that prograded from the master fault towards the basin centre. On the dipslope glacio‐eustatic signals outperformed tectonic influence on deposition. Sea level lowstands promoted deposition of red sabkha mudstones and gypsum/anhydrite, salinas evaporites or dissolution breccias, interbedded with highstand carbonate beds.
This paper presents a comparative analysis of the thicknesses–displacement relationships of fault cores in non-/low-porous carbonate and porous sandstone reservoirs. Fault thickness data were collected from extensional faults in mainly Cretaceous continental sandstones and Late Cretaceous–Paleogene marine carbonates exposed along the eastern flank of the Suez Rift, Egypt. The dataset consists of 730 thickness measurements, of which 313 are from 68 faults in carbonate rocks, and 417 are from 120 deformation band/microfaults and faults in sandstones. These data show that the increase in fault core thickness with displacement for the two lithologies is, overall, similar in log–log space, consistent with a power-law trend with an exponent of 0.5. However, for smaller faults, cores in carbonates are generally thicker than those in sandstones. The observation of nearly equal core thickness–displacement relationships for larger faults (>10 m displacement) suggests that increased displacement reduces the geomechanical influence of lithology. In a statistical analysis of bins of fault displacement, small displacement faults seem to follow a skewed distribution towards smaller fault core thicknesses, moderate displacement faults have a normal distribution, while large displacement faults have a distribution skewed towards large core thicknesses. Each thickness distribution can be estimated with a mean and standard deviation. Fault core thickness variations are caused by interplaying factors such as fault geometric development, spatial and temporal positioning of shear and volumetric strains, and rheological changes. The variability in core thickness and intrinsic architecture of fault cores for any given location will cause significant variation in across-fault fluid flow, even for the same juxtaposition style.