Lauri Siivonen

Lauri Siivonen

Auto-generated profile, based on publicly available information

Lauri Siivonen

Tampere University of Technology, Tampere, Finland

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2009 in International Journal of Fluid Power
Verified
Journal Article
Closed access
LSLauri Siivonen
Lauri Siivonen
Matti LinjamaMatti Linjama
Matti Linjama
MHMikko Huova
Mikko Huova
MVMatti Vilenius
Matti Vilenius
The digital valve system is an on/off valve based directional flow control valve capable of accurate control of hydraulic actuators. The presented system has good features concerning fault tolerance since it can detect, diagnose and compensate faults on-line. This paper concentrates on fault compensation when a valve has jammed in the open—position and the system has internal leakage. The system can adapt to the fault and continue operation with only a small degradation in performance. This feature is unique in the area of hydraulics since the system has no extra components added. The cost for this compensation is increased calculation in the controller and increased energy consumption if a fault occurs. If these downsides can be accepted the system can be considered fault-tolerant and it could be used even in critical applications where failing is not an option. Fault tolerance can also be introduced as standard in every modern hydraulic application where good performance and fault tolerance are needed.

1 September 2019 in Fusion Engineering and Design
Verified
Journal Article
Closed access
LSLauri Siivonen
Lauri Siivonen
MPMiika Paloniitty
Miika Paloniitty
Matti LinjamaMatti Linjama
Matti Linjama
HSHarri Sairiala
Harri Sairiala
SESalvador Esqué
Salvador Esqué

12 September 2018
Verified
Conference Paper
Closed access
PDF file
MHMikko Huova
Mikko Huova
Matti LinjamaMatti Linjama
Matti Linjama
LSLauri Siivonen
Lauri Siivonen
TDTill Deubel
Till Deubel
HFHeino Försterling
Heino Försterling
ESEdgar Stamm
Edgar Stamm
This paper studies a novel on/off-valve-based fine positioning method for hydraulic drives. The method proposed utilizes four on/off-valves in independent metering configuration to reach good positioning accuracy and low power losses. Previously, servo valves have been used in precise position control of hydraulic double acting cylinders. Another approach uses on/off-valves, which are typically driven by using pulse width modulation (PWM) or, if there are parallel connected valves, pulse code modulation (PCM). Typically, both cylinder sides are modulated simultaneously. The new concept proposed uses a cylinder model to calculate a correct opening sequence for the on/off-valves, such that the target piston position is reached. The method proposed modulates single cylinder side at a time in order to achieve small piston position step sizes. Despite relying on the modelled compressibility of the fluid, the method presented requires no knowledge about the bulk modulus of the fluid. It is enough that the bulk modulus of the fluid in both cylinder chambers can be assumed equal. The paper includes the design of the control method, a simulation study proving the validity of the method, and an experimental part investigating the performance in practice. The experimental results show a positioning accuracy of +/− 1 μm with an on/off-valve-based hydraulic drive, the maximum velocity of which is 0.7 m/s.

31 December 2019 in Rakenteiden Mekaniikka
Verified
Journal Article
Open access
PDF file
LSLauri Siivonen
Lauri Siivonen
MPMiika Paloniitty
Miika Paloniitty
Matti LinjamaMatti Linjama
Matti Linjama
AHAntti Hynnä
Antti Hynnä
SLSirpa Launis
Sirpa Launis
Vacuum brazed steel-copper laminate could be used in high-pressure hydraulic manifolds in order to reduce size, weight and allow use of complex designs. The durability of such material is unknown. Samples were manufactured and static and dynamic tests were conducted. Results showed reduced material performance due to heat treatment. A hydraulic test manifold was manufactured and a long-term pressure load test was conducted. The material showed surprisingly good durability and pressure hull did not break in tests. A microscopic study was performed and only solidified copper in the corners had micro cracks after 10 million test cycles.

1 January 2011
Verified
Conference Paper
Closed access
MHMika Herranen
Mika Herranen
LSLauri Siivonen
Lauri Siivonen
KHKalevi Huhtala
Kalevi Huhtala

16 October 2017
Verified
Conference Paper
Closed access
PDF file
LSLauri Siivonen
Lauri Siivonen
KHKalevi Huhtala
Kalevi Huhtala
Steerable thrusters are used to maneuver a vessel in open sea environment. The harsh environment of arctic seas introduces certain challenges with propellers hitting ice and decreasing lifetime of the system, as the loads generated by ice impacts are significantly higher than nominal loads. Damping of an ice impact load is a difficult task since the impacts have high torsional loads and they occur only in a fraction of the lifetime of the system. Commercial dampers are hard to find since they do not generally have the capacity for damping such high loads. The proposed active hydraulic damper reduces ice impact loads by accelerating and decelerating the shaft line. The lack of space and commercial components narrow down the possibilities but simulation results with the system show some positive effects in typical ice impact scenario. The system also recuperates most of the used energy and stores it to accumulator.