22 May 2019 in IEEE Journal of Photovoltaics
This paper presents an experimental investigation of the temperature coefficients of multicrystalline silicon solar cells. The aim was to determine if some cell parameters can affect positively the temperature sensitivity without detrimental impact on the efficiency. Commercial solar cells with different bulk resistivities, compensation levels, and cell architectures have been studied. We report that the base net doping, the location of the solar cell along the brick and the cell architecture have significant impacts on the temperature coefficients. Moreover, we show how the change in recombination mechanisms along the ingot height affects the temperature coefficients. The compensation level was observed to have no significant effect on the temperature coefficients. We also demonstrate why aluminum back-surface-field and passivated emitter rear contact solar cells have similar temperature sensitivities despite a better passivation and higher open-circuit voltage for the latter cell architecture. Finally, we have found that reducing the bulk resistivity can improve the solar cells’ performance in hot climates.
9 June 2022 in IEEE Journal of Photovoltaics
This article presents new analytical expressions for the temperature coefficients of the voltage, current, and power of a solar cell at its maximum power point (MPP). A new analytical expression of the temperature coefficient of the fill factor is also derived. The new expressions are written as functions of photovoltaic (PV) metrics that can be obtained from i-V measurements. Nonideal diode behavior is partially accounted for through a temperature dependent ideality factor. The recombination parameter $\gamma$, which has been shown to account for the thermal sensitivity of all mechanisms determining the open-circuit voltage, appears to play a role also for the temperature coefficient of the MPP. The expressions are tested against experimental data, which covers measurements from 18 multicrystalline silicon solar cells with different bulk resistivities and cell architectures. It is found that the new model captures the essence of the temperature variation shown by the investigated PV metrics.
13 December 2019 in IEEE Journal of Photovoltaics
In this article, we present a method to obtain implied open-circuit voltage images of silicon wafers and cells at different temperatures. The proposed method is then demonstrated by investigating the temperature coefficients of various regions across multicrystalline silicon wafers and cells from different heights of two bricks with different dislocation densities. Interestingly, both low and high temperature coefficients are found in dislocated regions on the wafers. A large spread of temperature coefficient is observed at regions with similar performance at 298 K. Reduced temperature sensitivity is found to be correlated with the increasing brick height and is exhibited by both wafers and cells. This may indicate that cells made from the top of the brick, although having higher defect concentration, actually suffer relatively less degradation in the performance at higher temperatures.
12 February 2020 in IEEE Journal of Photovoltaics
This article investigates the influence of crystallographic defects on the temperature sensitivity of multicrystalline silicon wafers. The thermal characteristics of the implied open-circuit voltage is assessed since it determines most of the total temperature sensitivity of the material. Spatially resolved temperature-dependent analysis is performed on wafers from various brick positions; intragrain regions, grain boundaries, and dislocation clusters are examined. The crystal regions are studied before and after subjecting the wafers to phosphorus gettering, aiming to alter the metallic impurity concentration in various regions across the wafers. Most intragrain regions and grain boundaries are found to show similar thermal characteristics before gettering. The gettering process has no substantial effect on the temperature sensitivity of intragrain regions, whereas it increases the sensitivity of most grain boundaries. Dislocation clusters exhibit both highest and lowest temperature sensitivities compared with other crystal regions before and after gettering. Images of the recombination parameter γ are created and related to the temperature sensitivity of the Shockley–Read–Hall (SRH) lifetime of the impurities in the material. The results suggest that most intragrain regions and grain boundaries are limited by SRH centers with a modest lifetime temperature sensitivity in the studied temperature range. Dislocation clusters are found to contain recombination centers with an effective lifetime that has a beneficial temperature sensitivity. The gettering process is observed to alter the composition of the recombination centers in the dislocation clusters, resulting in an SRH lifetime with an even more favorable temperature sensitivity for most clusters.
1 May 2023 in IEEE Journal of Photovoltaics
The recombination parameter $\gamma$ appears in mathematical expressions for the temperature coefficient of solar cells. This work presents a new analytical expression for this parameter. The expression is derived assuming that all nonradiative recombination occurs in the neutral region of the cell, where carrier diffusion is the dominant transport mechanism. The model shows a direct relation between $\gamma$ and the temperature sensitivities of the carrier mobility and lifetime. Problems concerning the original definition of $\gamma$ and its temperature and voltage dependence are discussed and, when possible, amended. A further investigation of the possibility of defect characterization through $\gamma$ is presented. This yields two analytical expressions that link $\gamma$ to defect characteristics. A numerical evaluation of the derived expressions is performed for a number of impurities. It is concluded that the recombination parameter $\gamma$ alone may not be suitable for defect characterization.