Geopolymers are inorganic polymers obtained through the alkaline activation of aluminosilicates. Due to their cementitious properties, they are being studied as a sustainable alternative to Portland cement. Red ceramic waste (RCW), being a source of silica and alumina, can serve as a precursor for producing geopolymers. In this work, we evaluated the feasibility of producing geopolymers from hollow brick (HB) and hydrated lime, using only sodium hydroxide as an alkaline activator. The test specimens were prepared replacement HB by up to 30 wt% of hydrated lime, aiming to evaluate the compressive strength after 7 and 28 curing days of the geopolymer produced. The results showed that samples with 30 wt% of hydrated lime, achieved the highest compressive strength (11.26 MPa) after 28 days of curing, although all values found were above the limit established by Brazilian standards for modular geopolymer bricks. The results therefore show a sustainable and widely viable implementation alternative to reduce the environmental impacts caused by the production of Portland cement.
Ni‐containing metal–organic frameworks (MOFs) have emerged as promising precursors for CO 2 hydrogenation due to their tunable structural properties. In this work, Ni‐MOFs were synthesized by a microwave‐assisted solvothermal method using 2‐methylimidazole as the organic ligand. The materials were characterized by x‐ray diffraction, thermogravimetric analysis (TGA), Raman and infrared spectroscopy, scanning electron microscopy (SEM), N 2 adsorption–desorption, and CO 2 temperature‐programmed desorption. The results showed that longer synthesis times promoted higher crystallinity, lower defect density, and improved structural organization. Microwave‐assisted synthesis also favored the formation of more homogeneous structures, directly influencing the properties of the derived catalysts after thermal decomposition and reduction. Catalytic evaluation revealed that the catalyst derived from the more organized MOF achieved the highest CO 2 conversion (>60%), producing both CO and CH 4 . In contrast, the catalyst derived from the less organized MOF exhibited lower CO 2 conversion but higher selectivity toward CH 4 . These results demonstrate that microwave‐assisted synthesis is an effective strategy for tuning the structural properties of Ni‐MOF precursors and controlling the catalytic behavior of the derived materials in CO 2 methanation.
Glass-ceramics based on the Na2O–Al2O3–SiO2 (NAS) system have attracted attention due to their potential in dental, refractory, and electronic applications, particularly associated with the nepheline (NaAlSiO4) phase. This study investigated the non-isothermal crystallization kinetics of a NAS glass containing CaO and TiO2 precursors (19.7 mol%) for the in situ formation of a glass-ceramic composed of nepheline and calcium titanate (CaTiO3). The kinetic parameters were determined using the Ligero method. The activation energy for crystallization (Ea) was equal to 195 ± 1 kJ/mol, remaining constant within the crystallized fraction range (x) of 0.40 to 0.50. The average Avrami index (n ≈ 2), associated with a saturated nucleation mechanism (m = 2), indicates a volumetric crystallization process. In addition, the time ratio (t0.75/t0.25 = 1.48) suggests crystal growth limited by diffusion, leading to the development of polyhedral morphologies. X-ray diffraction (XRD) analysis confirmed the formation of nepheline and CaTiO3 phases after heat treatment, while scanning electron microscopy (SEM) revealed a microstructure composed of polyhedral crystals, supporting the kinetic interpretation.
Cement production, the primary material used in construction industry, accounts for around 8% of global CO2 emissions. In addition to the demand for materials that emit greenhouse gases, the sector generates approximately 50% of solid waste in Brazilian cities. Geopolymers, which utilise industrial by-products rich in chemically activated aluminosilicates, are emerging as a sustainable alternative to Portland cement. One of the main components of brazillian construction and demolition waste (CDW) is red ceramic, which, due to its firing temperature, contains a high proportion of metakaolinite, an amorphous, pozzolanic and highly reactive aluminosilicate. This study aims to develop a sustainable sealing brick using CDW as the main geopolymer precursor. CDW was activated with highly basic NaOH solutions to form the geopolymer paste. Pulverised CDW was analysed by XRF and XRD, confirming presence of Al and Si, as well as crystalline phases such as α-quartz (SiO2), hydrated calcium silicate (CaH2O4Si) and calcite (CaCO3). After determining the solid/liquid ratio (Casagrande apparatus), cylindrical test specimens were prepared using mixtures of CDW, hydrated lime and alkaline solution in four compositions. Compression tests on the probes exceeded the minimum compressive strength value specified by brazilian (>1.5 MPa) and european (>2.5 MPa) standards for fired ceramic bricks.