Organic/inorganic hybrid structures are considered innovative alternatives for the next generation of low-cost photovoltaic devices because they combine advantages of the purely organic and inorganic versions. Here, we report an efficient hybrid solar cell based on sub-wavelength silicon nanotexturization in combination with the spin-coating of poly (3,4-ethylene-dioxythiophene):polystyrenesulfonate (PEDOT:PSS). The described devices were analyzed by collecting current-voltage and capacitance-voltage measurements in order to explore the organic/inorganic heterojunction properties. ALD deposited ultrathin aluminium oxide was used as a junction passivation layer between the nanotextured silicon surface and the organic polymer. The measured interface defect density of the device was observed to decrease with the inclusion of an ultrathin Al2O3 passivation layer leading to an improved electrical performance. This effect is thought to be ascribed to the suppression of charge recombination at the organic/inorganic interface. A maximum power conversion efficiency in excess of 10% has been achieved for the optimized geometry of the device, in spite of lacking an antireflection layer or back surface field enhancement schemes.
This paper describes the synthesis and characterization of Si and CdTe quantum dots (QDs) and their use, either on their own or combined, as photoluminescent (PL) down-shifting nanostructured coatings aimed to enhance the photovoltaic efficiency of polycrystalline silicon solar cells. To this end, the front face of a set of silicon cells was coated with different volume ratios of the above-mentioned QDs, or some of its mixtures, dispersed in PMMA layers. Previously, the absorption and the PL (exc = 380 nm) response of the dispersions of the QDs were measured. It was observed that the PL response of the mixtures was strongly affected in location, spread, and intensity of the emission peak according to the volume ratio involved. As compared to the unmixed CdTe samples, a notorious red-shift of the main peak location was obtained for a couple of mixed QDs’ dispersions, which was one of the project objectives given that Si solar cells respond better to photons with wavelengths in the 650–700 nm range. This effect was confirmed in a set of polycrystalline Si solar cells covered with and without nanostructured PMMA/QDs layers tested under AM 1.5G solar simulator conditions. It was found that the use of the proposed mixtures of QDs gave an increase of 1.53% in solar cell power conversion efficiency.
Stress dependent micromagnetic modeling based on the Landau–Lifshitz–Gilbert equations evinces a remarkable relationship between uniaxial stress in ferromagnetic (FM) thin films and the pumped spin current density, and elucidates the influence of compressive and tensile stress on the static and dynamic magnetization of FM thin films, and FM/normal-metal (NM) heterostructures. Thus, the presence of deformation in the structure through a stress-mediated magnetoelectric-coupling triggers a change in the magnetic anisotropy field in ferromagnets via magnetostriction. In our micromagnetic simulations we considered yttrium iron garnet (YIG) as the FM layer and platinum the NM for the spin-pumped current calculations, and the stress contribution was introduced as an additional term in the effective anisotropy constant which also comprised the magnetocrystalline and shape anisotropy contributions of YIG. Ostensibly, the dynamic control of the stress-dependent magnetization enables the tailoring of the magnetic anisotropy field to achieve the amplitude modulation of the pumped spin current density. The predicted ability to dynamically modulate the pumped spin current density is anticipated to benefit multifarious spintronic applications.
High-quality perovskite films are the key factor in manufacturing high performance devices along with outstanding optoelectronic properties. However, methylammonium Lead Iodide (MAPbI3) perovskites are prone to defect formation during the iodide and methylamine ion defect migration. To achieve stable passivation in the perovskite film, additive engineering with nanoparticles can be used as an effective method to passivate the crystal defects. The carboxylic, hydroxyl and amino groups of Carbon Quantum Dots (CQDs) can bond the uncoordinated Pb atoms of the perovskite film creating strong and stable interactions inducing a low trap-state density improving the optoelectronic properties of the perovskite film. Therefore, we study the different functional groups in CQDs by Raman, FTIR, absorbance and photoluminice spectra and propose the addition of CQDs in the perovskite film to reduce the crystal defects and passivate the grain boundaries.