Kevin Prawiranto

Kevin Prawiranto

Auto-generated profile, based on publicly available information

Kevin Prawiranto

Empa, Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Biomimetic Membranes and Textiles, CH-9014 St. Gallen, Switzerland

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2019 in Resources, Conservation and Recycling
Verified
Journal Article
Closed access
TDThijs Defraeye
Thijs Defraeye
GTGiorgia Tagliavini
Giorgia Tagliavini
WWWentao Wu
Wentao Wu
KPKevin Prawiranto
Kevin Prawiranto
SSSeraina Schudel
Seraina Schudel
ABAndreas Bühlmann
Andreas Bühlmann

4 April 2019 in RSC Advances
Verified
Journal Article
Open access
PDF file
KPKevin Prawiranto
Kevin Prawiranto
TDThijs Defraeye
Thijs Defraeye
DDDominique Derome
Dominique Derome
ABAndreas Bühlmann
Andreas Bühlmann
SHStefan Hartmann
Stefan Hartmann
JCJan Carmeliet
Jan Carmeliet
A good understanding of the microstructural changes due to dehydration is critical to optimize fruit drying processes. By using X-ray micro-computed tomography, we quantified the changes in porosity, pore diameter, cell sphericity, cell diameter and cell elongation of apple parenchyma tissue during multiple convective drying scenarios: natural convection (air speed = 0.05 m s−1), forced convection (air speed = 0.5 m s−1) and coupled irradiation-convective drying (air speed = 0.05 m s−1 with radiation heating). Drying conditions affected the microstructure noticeably, in particular the formation of an elevated-porosity layer (tissue region where the porosity was higher than the initial porosity) and a deformed-cell layer (tissue region where the sphericity of the cells was lower than 0.75) near the sample surface. Using the combination of Eulerian and Lagrangian approaches, we linked the formation of the aforementioned layers to bulk shrinkage and deformation of individual cells. Forced convective drying resulted in a more porous structure and a higher degree of cell deformation compared to the other drying cases. Meanwhile, the coupled irradiation-convective drying induced the largest bulk shrinkage. The latter was caused by a large reduction in pore volume and the formation of large cell clusters in the deformed-cell layer.

1 December 2017 in Journal of Food Engineering
Verified
Journal Article
Closed access
TDThijs Defraeye
Thijs Defraeye
WWWentao Wu
Wentao Wu
KPKevin Prawiranto
Kevin Prawiranto
GFGiuseppino Fortunato
Giuseppino Fortunato
SKShelley Kemp
Shelley Kemp
BNBart Nicolai
Bart Nicolai

1 December 2018 in Journal of Food Engineering
Verified
Journal Article
Open access
KPKevin Prawiranto
Kevin Prawiranto
TDThijs Defraeye
Thijs Defraeye
DDDominique Derome
Dominique Derome
PVPieter Verboven
Pieter Verboven
BNBart Nicolai
Bart Nicolai
JCJan Carmeliet
Jan Carmeliet

8 October 2020 in Soft Matter
Verified
Journal Article
Closed access
PDF file
KPKevin Prawiranto
Kevin Prawiranto
JCJan Carmeliet
Jan Carmeliet
TDThijs Defraeye
Thijs Defraeye
Convective drying of fruits leads to microstructural changes within the material as a result of moisture removal. In this study, an upscaling approach is developed to understand and identify the relation between the drying kinetics and the resulting microstructural changes of apple fruit, including shrinkage of cells without membrane breakage (free shrinkage) and with membrane breakage (lysis). First, the effective permeability is computed from a microscale model as a function of the water potential. Both temperature dependency and microstructural changes during drying are modeled. The microscale simulation shows that lysis, which can be induced using various pretreatment processes, enhances the tissue permeability up to four times compared to the free shrinkage of the cells. Second, via upscaling, macroscale modeling is used to quantify the impact of these microstructural changes in the fruit drying kinetics. We identify the formation of a barrier layer for water transport during drying, with much lower permeability, at the tissue surface. The permeability of this layer strongly depends on the dehydration mechanism. We also quantified how inducing lysis or modifying the drying conditions, such as airspeed and relative humidity, can accelerate the drying rate. We found that inducing lysis is more effective in increasing the drying rate (up to 26%) than increasing the airspeed from 1 to 5 m s−1 or decreasing the relative humidity from 30% to 10%. This study quantified the need for including cellular dehydration mechanisms in understanding fruit drying processes and provided insight at a spatial resolution that experiments almost cannot reach.

20 August 2020 in engrXiv
Verified
Preprint
Open access
KPKevin Prawiranto
Kevin Prawiranto
SYSyamsudin
Syamsudin
HSHerri Susanto
Herri Susanto
Sludge cake is a type of solid waste in pulp and paper mills which may harm the environment if disposed without treatment. Its proximate analysis (adb) are: ash 26.74%; volatile matter 59.09%; fixed carbon 11.04%; moisture 3.13%, while its ultimate analysis (adb) are: C 33.46%; H 4.5%; N 1.14%; S 0.35%; O 33.81%. Having a calorific value of 3000 cal/g (adb), sludge cake may be used as renewable fuel. Unfortunately it has a high water content, so reduction of water content become a main concern in utilizing sludge cake. A combination of mechanical dewatering and thermal drying has been considered for water removal with a minimum energy consumption. Moreover, the application of pressurized mechanical dewatering may also play a role in formation of briquettes.Experiments on mechanical dewatering and thermal drying were carried out using 50 g sludge cake with initial water content 73%. With a pressure of 400 kg/cm2 for compression, water content at the end of mechanical dewatering was 57%. This dewatered slugde was subsequently treated using thermal drying to a moisture content of 15%. Calculated total energy for this combination of mechanical dewatering and thermal drying was about 1080 J/g. This value was lower than the energy consumption of 1520 J/g required for direct thermal drying from its moisture content of 73% down to 15%. Experiments on the use of coal powder as compression aid were also trial to improve sludge dewaterability and briquettes calorific value. Mechanical dewatering of slugde with addition of 20%-w/w coal powder resulting a briquette with moisture content of 38% at compression pressure of 400 kg/cm2. The drying curves of briquette did not affected with its size if its diameter was less than 0.5 cm. Briquette with 1 cm thickness took significantly more time to remove its water content.