Solaiman Mohammad

Solaiman Mohammad

Auto-generated profile, based on publicly available information

Solaiman Mohammad


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
ASAhmad Saadi Samra
Ahmad Saadi Samra
MAMuhammad Ahmad
Muhammad Ahmad
SMSolaiman Mohammad
Solaiman Mohammad
MHMuhammad Husnain
Muhammad Husnain
SSSamra Sajjad
Samra Sajjad
R.  A. ShakoorR. A. Shakoor
R. A. Shakoor
High-performance coatings capable of resisting mechanical wear and corrosive degradation are increasingly required for structures exposed to severe service conditions. To address this challenge, Ni-P coatings reinforced with TiB₂ nanoparticles were produced via electrodeposition on mild steel substrates. The TiB₂ content was varied between 0.25 and 1.00 g/L⁻¹, and comprehensive characterization was conducted using structural, morphological, mechanical, tribological, and electrochemical techniques. XRD and microscopic analyses confirmed effective nanoparticle incorporation, with homogeneous dispersion observed up to 0.75 g/L⁻¹. This optimized concentration promoted grain refinement, reduced porosity, and enhanced coating compactness. Mechanical performance improved significantly, with the 0.75 g/L⁻¹ coating showing the highest hardness, corresponding to an increase of approximately 27.53% ± 6% compared with the unreinforced Ni-P layer. Wear testing indicated substantial reductions in both wear rate and friction coefficient, attributed to the rolling and solid-lubricant behavior of TiB₂ nanoparticles. Electrochemical evaluation demonstrated superior corrosion protection, achieving a protection efficiency of ~97.5% and an Rct value of 7.84 kΩ·cm² in 3.5 wt.% NaCl solution. In contrast, excessive TiB₂ addition (1.00g/L⁻¹) led to particle agglomeration and localized structural defects, resulting in diminished performance. Numerical simulations using COMSOL Multiphysics supported these findings by revealing non-uniform current density distribution and thickness variations associated with particle-induced perturbations. These results confirm that properly optimized TiB₂ reinforcement significantly enhances the multifunctional performance of Ni-P coatings designed for harsh operational conditions.

29 August 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
SMSolaiman Mohammad
Solaiman Mohammad
MAMuhammad Ahmad
Muhammad Ahmad
UJUsama Javed
Usama Javed
KAKamran Ali
Kamran Ali
BMBilal Mansoor
Bilal Mansoor
R.  A. ShakoorR. A. Shakoor
R. A. Shakoor
Exposure of steel to corrosive and wear-intensive environments accelerates degradation and shortens service life, motivating protective nanocomposite coatings. In this study, A36 carbon steel was coated with electroless Ni–P/WC nanocomposites containing 0.25, 0.50, and 0.75 g L−1 WC nanoparticles. Structural and morphological analyses confirmed WC incorporation into the Ni–P matrix, while mechanical, tribological, erosive, and corrosion performance was evaluated relative to unreinforced Ni–P. The optimized coating containing 0.50 g L−1 WC increased microhardness from approximately 470 to 876 HV50, corresponding to an 86% improvement, and increased nanoindentation hardness by 56%. It also reduced wear rate by 62% and erosion-crater depth by approximately 50%. Electrochemical testing in 3.5 wt.% NaCl showed a 93% reduction in corrosion current density and a maximum protection efficiency of 92.6%. After 28 days of salt immersion, mass loss decreased from 4.00 to 1.20 mg and corrosion rate from 0.0232 to 0.0070 mm year−1, representing a 70% reduction and confirming improved long-term barrier performance. An exploratory machine-learning framework used WC concentration, deposition time, and bath temperature as inputs, with microhardness and corrosion current density as outputs. Random Forest and K-nearest-neighbor regression were compared as ensemble-based and distance-based approaches. Random Forest performed better, achieving R2 values of approximately 0.85 for both responses and Pearson correlation coefficients above 0.98, whereas KNN showed weaker predictive performance. Feature-importance analysis identified WC concentration as the dominant factor controlling hardness and corrosion response.